9 More Discussions You Might Find Interesting
1. Slackware
Need to free up a usb port for webcam. What does xorg.conf look like in order to work if I move mouse to PCI port via a converter plug? (1 Reply)
Discussion started by: slak0
1 Replies
2. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
3. Programming
For a project that I'm working on I want to write a low level PCI driver, but I can't seem to find any free/cheap documentation on PCI firmware specifications. I came across the "pci firmware specification 3.0" manual but this costs USD $1000 :eek:. I am not developing a commercial product... (13 Replies)
Discussion started by: neur0n
13 Replies
4. UNIX for Dummies Questions & Answers
Is there an easy way to setup a cross-over cable (USB-USB) between a linux box and a windows PC? My 2 machines are next to each other but I really do not want to keep transfering my files using my USB drive.
Thanks! (4 Replies)
Discussion started by: Xterra
4 Replies
5. Linux
I installed PCI Card HP SC44Ge - SAS1068E
on my linux CentOS 5.4
is there a way to find out if the PCI is properly installed and recognized by linux.
lspci is enough?
just to add that PCI card is connected to a tape...
also how can I find out driver and firmware version?
thanks a... (1 Reply)
Discussion started by: karlochacon
1 Replies
6. UNIX for Dummies Questions & Answers
platform: sunblade 100
Solaris 10.
When running a test-all from the ok prompt on this new (to me) system, it locks up at pci@1f,0/usb/c,3. It's been there for about 25 minutes.
I do have a usb keyboard and mouse attached, both are known good. There is no flash stick/ thumb drive... (0 Replies)
Discussion started by: montana77
0 Replies
7. UNIX for Dummies Questions & Answers
Hi,
im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the... (0 Replies)
Discussion started by: jestra
0 Replies
8. Solaris
How do I get the PCI ID for my Realtek adapter?
It's a Solaris x86 installation. (5 Replies)
Discussion started by: kuultak
5 Replies
9. BSD
Hi!
I just wanted to know what network cards are supported in FreeBSD. I have looked at the list of supported cards but I can't find any of them in the stores. Is the list not updated, I would really preciate info about where (in EU, Sweden) I can buy them.
/Peter (2 Replies)
Discussion started by: Barfly.se
2 Replies
UFTDI(4) BSD Kernel Interfaces Manual UFTDI(4)
NAME
uftdi -- USB support for serial adapters based on the FT8U100AX and FT8U232AM chips
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device uftdi
device ucom
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
uftdi_load="YES"
DESCRIPTION
The uftdi driver provides support for various serial adapters based on the FTDI FT2232C, FT8U100AX and FT8U232AM chips.
The device is accessed through the ucom(4) driver which makes it behave like a tty(4).
HARDWARE
The uftdi driver supports the following adapters:
o B&B Electronics USB->RS422/485 adapter
o Elexol USB MOD1 and USB MOD3
o HP USB-Serial adapter shipped with some HP laptops
o Inland UAS111
o QVS USC-1000
o Buffalo PC-OP-RS / Kurouto-shikou KURO-RS universal remote
o Prologix GPIB-USB Controller
SEE ALSO
tty(4), ucom(4), usb(4)
HISTORY
The uftdi driver appeared in FreeBSD 4.8 from NetBSD 1.5.
BSD
November 22, 2006 BSD
