10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi All
I have a file which contains the timestamp of the log and a message and I want to implement a polling mechanism, where this log file is pooled every 2 minutes and list the errors in the file. I want to list down the errors only after the timestamp in the file is more than the current... (2 Replies)
Discussion started by: infyanurag
2 Replies
2. Shell Programming and Scripting
I am often given log files at work in .csv format to work with, normally extracting various fields. I then have to figure out the number of each field so that I can extract that field with cut or awk. Normally I just manually count the fields, based on the field separator. I would like to be... (3 Replies)
Discussion started by: stumpyuk99
3 Replies
3. UNIX for Dummies Questions & Answers
Hi All,
I would like to know couple of ways to list the content available in tar and gzipped file without extracting.
i.e., I would like to display the contents of test.tar.gz without extracting.
Note :: please suggest a command other that tar -ztvf (9 Replies)
Discussion started by: Girish19
9 Replies
4. Solaris
Hi,
We replaced one of our tape drives (attached to a SPARC Server) with an LTO5 one (external, attached vi SAS). Manually we check (using tar) that the OS can write data to the Tape Drive, however, the application backup is failing.
Since the application takes its own backup, the apps team... (0 Replies)
Discussion started by: Mack1982
0 Replies
5. SCO
Hi.
I have this old server onto which i needed to list the content of a tape. This is a SCO box (SCO_SV 3.2 5.0.6 i386) and backup was done using cpio.
#tape status
status : ready beginning-of-tape
soft errors : 0
hard errors : 0
underruns : 0
#dtype /dev/rct0
/dev/rct0 ... (5 Replies)
Discussion started by: Stephan
5 Replies
6. AIX
had this p520 server connected to a DDS-3 4mm tape drive...
running AIX 7.1 TL01 -- the latest release.
mksysb -i -e /dev/rmt/1 ..tells me only 1% is done after over an hour ...
I had no problems with th hardware and other connections...
tar command to /dev/rmt/1 runs very fast ....... (3 Replies)
Discussion started by: ppchu99
3 Replies
7. Solaris
Hi fellows,
Can you please share any command with which I can list down the file names inside a tar.gz file.
I have tried with these possibilities but in vain.
bash-3.00$ tar -ztvf file.tar.gz
tar: z: unknown function modifier
bash-3.00$ tar ztvf file.tar.gz
tar: z: unknown function... (1 Reply)
Discussion started by: Zaib
1 Replies
8. UNIX for Dummies Questions & Answers
Hello guys,
I am having a requirement,
I am having three file m1,m2,m3 having some contents. I want to list last 20 lines of m1,m2 and m3 all together on the terminal.
I used tail -20 m1 m2 m3,
but it is showing error,
tail: option used in invalid context -- 2
Can u help me... (2 Replies)
Discussion started by: mraghunandanan
2 Replies
9. UNIX for Dummies Questions & Answers
I'm pulling a 1MB file from tape using tar. It's a 300GB DLT tape and it does have a lot of files on it because it's go the entire OS and Oracle RMAN files and 3000 table exports, but it's taking 2-3 hours to pull this file off of it. Is this type of performance what I should expect?
The... (0 Replies)
Discussion started by: citrowske
0 Replies
10. HP-UX
HI All
I have created the bootable recovery tape using the ignite command make_tape_recovery, I need help for the command to list the content recorded in that tape.
Regards,
Gege:confused: (1 Reply)
Discussion started by: cgege
1 Replies
BACKUP_QUIT(8) AFS Command Reference BACKUP_QUIT(8)
NAME
backup_quit - Leaves interactive mode
SYNOPSIS
quit [-help]
q [-h]
DESCRIPTION
The backup quit command exits interactive mode, returning the issuer to the regular shell prompt at which the backup or backup interactive
command was issued to enter interactive mode. The command has no effect when issued outside interactive mode. Issuing the Ctrl-D command
also exits interactive mode.
CAUTIONS
To exit interactive mode, all jobs must be completed. Use the backup jobs command to list any jobs currently pending or executing, and the
backup kill command to terminate them as necessary.
OPTIONS
-help
Prints the online help for this command. All other valid options are ignored.
EXAMPLES
The following command exits interactive mode:
backup> quit
%
PRIVILEGE REQUIRED
None
SEE ALSO
backup(8), backup_interactive(8), backup_jobs(8), backup_kill(8)
COPYRIGHT
IBM Corporation 2000. <http://www.ibm.com/> All Rights Reserved.
This documentation is covered by the IBM Public License Version 1.0. It was converted from HTML to POD by software written by Chas
Williams and Russ Allbery, based on work by Alf Wachsmann and Elizabeth Cassell.
OpenAFS 2012-03-26 BACKUP_QUIT(8)