10 More Discussions You Might Find Interesting
1. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
2. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
3. UNIX for Dummies Questions & Answers
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies
4. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
5. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
6. AIX
Hi,
I want to know wheather partition size for installation of vio client can be specified on vio server
example
If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Discussion started by: manoj.solaris
1 Replies
7. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
8. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
9. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
10. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
DHCP-HELPER(8) System Manager's Manual DHCP-HELPER(8)
NAME
dhcp-helper - A DHCP/BOOTP relay agent.
SYNOPSIS
dhcp-helper [OPTION]...
DESCRIPTION
dhcp-helper is a DHCP and BOOTP relay agent. It listens for DHCP and BOOTP broadcasts on directly connected subnets and relays them to DHCP
or BOOTP servers elsewhere. It also relays replies from the remote servers back to partially configured hosts. Once hosts are fully config-
ured they can communicate directly with their servers and no longer need the services of a relay.
OPTIONS
The only required option is at least one DHCP server to relay to. The simplest way to configure dhcp-helper on a router is just to give the
interface to the network containing the DHCP server with a -b option. All the other interfaces present on the machine will then accept DHCP
requests. On a machine which does not have an interface on the network containing the DHCP server, use a -s option instead.
-s <server>
Specify a DHCP or BOOTP server to relay to. The server may be given as a machine name or dotted-quad IP address. More than one
server may be specified.
-b <interface>
Relay to a DHCP or BOOTP server using broadcast via <interface>. This eliminates the need to give a server address. <interface> is
automatically added to the list of interfaces which will not receive DHCP requests.
-i <interface>
Specify which local interfaces to listen on for DHCP/BOOTP broadcasts. If no -i flags are given all interfaces are used except those
specified by -e flags and those specified by -b flags.
-e <interface>
Specify which local interfaces to exclude.
-p Use alternative ports (1067/1068) for the DHCP client and server.
-v Report the software release version and copyright information.
-d Debug mode, do not change UID, write a pid-file or go into the background.
-r <file>
Specify an alternate path for dhcp-helper to record its process-id in. Normally /var/run/dhcp-helper.pid.
-u <username>
Specify the userid to which dhcp-helper will change after startup. The daemon must normally be started as root, but it will drop
root priviledges after startup by changing id to another user. Normally this user is "nobody" but that can be over-ridden with this
switch.
NOTES
Dhcp-helper requires a 2.2 or later Linux kernel. The "Linux packet filter" and "packet socket" facilities are not required, which is the
chief advantage of this software over the ISC DHCP relay daemon.
AUTHOR
This manual page was written by Simon Kelley <simon@thekelleys.org.uk>.
DHCP-HELPER(8)
network interfaces on vio server