10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
2. AIX
picked up an old p520..and also spend sometimes to manage software:
a) AIX 7.1
b) VIOS Server 2.2
attempting to run a few LPARs without much more $$$$, as this is a home-made projects..
machine hdisk0, pre-installed with AIX 7.1
a few questions:
a) In order to run LPARs, I will... (7 Replies)
Discussion started by: ppchu99
7 Replies
3. AIX
trying to put VIO server software into this p520, firmware upgraded to the latest and greatest..SF240_415_318 , I think
a few questions, on this practice AIX machine on AIX 7.1
VIO can only be installed if ASMI or HMC is running ???
if so, perhaps ASMI is much simpler, since I will need to... (2 Replies)
Discussion started by: ppchu99
2 Replies
4. AIX
it shows up after the upgrade to SF240_415, after 2 hrs.
amber light shows up on the led of 9111-520, but alog shows:
everything seems to work, not sure what's going on.. (6 Replies)
Discussion started by: ppchu99
6 Replies
5. AIX
I have software running under AIX 5.3 that should communicate with a special device using standard communication protocol (Modbus) using serial RS-232 line
The settings are correct in both sides, But I can't establish a connection.
I suspect that there's something that I should do regarding the... (3 Replies)
Discussion started by: ayman metwally
3 Replies
6. AIX
Hi Folks,
I am a new AIX user. This is my first post in the UNIX forums. I did do a little bit of search before creating this post, but did not find any conclusive information. I am trying to connect to the service processor of an older 44p Model 170 box using my laptop. The 44p box has two... (6 Replies)
Discussion started by: shaell
6 Replies
7. AIX
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
Discussion started by: guttew
1 Replies
8. AIX
hello everybody.
Has anyone tried to install aix 5.2 on p520 machines. I've been trying but in the installation menu it says, "no disk found". I've used the same CD on a different 520 server and its working fine on it. Can anyone help, please? (5 Replies)
Discussion started by: soahel
5 Replies
9. AIX
I dont have an ascii terminal to hook upto this thing, trying to use my laptop but it doesnt seem to want to communicate, is there a special cable i should be using for this? (1 Reply)
Discussion started by: BG_JrAdmin
1 Replies
10. HP-UX
I am receiving messages from HP-UX Server
"The operating system is unable to communicate with the service processor.
The support bus which connects the system processors, the service processor and the Power Monitor or Platform Monitor may have become hung ".
I need help in the following:... (1 Reply)
Discussion started by: cgege
1 Replies
TCPSER(1) General Commands Manual TCPSER(1)
NAME
tcpser - emulate a Hayes compatible modem
SYNOPSIS
tcpser -d dev -s speed [-l log_level -t tracing_options] ...
tcpser -v port [-l log_level -t tracing_options] ...
DESCRIPTION
This manual page documents briefly the tcpser command.
tcpser turns a PC serial port into an emulated Hayes compatible modem that uses TCP/IP for incoming and outgoing connections. It can be
used to allow older applications and systems designed for modem use to operate on the Internet. tcpser supports all standard Hayes com-
mands, and understands extended and vendor proprietary commands (though it does not implement many of them). tcpser can be used for both
inbound and outbound connections.
OPTIONS
A summary of options is included below.
-h Show summary of options.
-p Port to listen on (defaults to 6400).
-t Trace flags: (can be combined)
s modem input
S modem output
i IP input
I IP output
-l Log level: 0 (NONE), 1 (FATAL) - 7 (DEBUG_X) (defaults to 0).
-L Log file (defaults to stderr).
The following can be repeated for each modem desired (-s, -S, and -i will apply to any subsequent device if not set again):
-d Serial device (e.g. /dev/ttyS0). Cannot be used with -v
-v TCP port for VICE RS232 (e.g. 25232). Cannot be used with -d
-s Serial port speed (defaults to 38400).
-S Speed modem will report (defaults to -s value).
-I Invert DCD pin.
-n Add phone entry (number=replacement).
-a Filename to send to local side upon answer.
-A Filename to send to remote side upon answer.
-c Filename to send to local side upon connect.
-C Filename to send to remote side upon connect.
-N Filename to send when no answer.
-B Filename to send when modem(s) busy.
-T Filename to send upon inactivity timeout.
-i Modem init string (defaults to `', leave off `at' prefix when specifying).
-D Direct connection (follow with hostname:port for caller, : for receiver).
AUTHOR
tcpser was written by Jim Brain <brain@jbrain.com>.
This manual page was written by Peter Collingbourne <pcc03@doc.ic.ac.uk>, for the Debian project (but may be used by others).
July 5, 2006 TCPSER(1)
