p520 Service Processor's IP

10 More Discussions You Might Find Interesting

1. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

2. AIX

running LPAR on power5 p520 hardware

picked up an old p520..and also spend sometimes to manage software: a) AIX 7.1 b) VIOS Server 2.2 attempting to run a few LPARs without much more $$$$, as this is a home-made projects.. machine hdisk0, pre-installed with AIX 7.1 a few questions: a) In order to run LPARs, I will...

3. AIX

VIO server on p520

trying to put VIO server software into this p520, firmware upgraded to the latest and greatest..SF240_415_318 , I think a few questions, on this practice AIX machine on AIX 7.1 VIO can only be installed if ASMI or HMC is running ??? if so, perhaps ASMI is much simpler, since I will need to...

4. AIX

p520 -- amber light

it shows up after the upgrade to SF240_415, after 2 hrs. amber light shows up on the led of 9111-520, but alog shows: everything seems to work, not sure what's going on..

5. AIX

P520 AIX com port (tty0) settings

I have software running under AIX 5.3 that should communicate with a special device using standard communication protocol (Modbus) using serial RS-232 line The settings are correct in both sides, But I can't establish a connection. I suspect that there's something that I should do regarding the...

6. AIX

Connecting to the service processor?

Hi Folks, I am a new AIX user. This is my first post in the UNIX forums. I did do a little bit of search before creating this post, but did not find any conclusive information. I am trying to connect to the service processor of an older 44p Model 170 box using my laptop. The 44p box has two...

7. AIX

LPAR processor/virtual processor settings

Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities. Environment is a 8-way p570 with 4 LPARs. lparVIO1 and lparVIO2: AIX 5300-04-01 Mode/Type= Shared-SMT/Capped Minimum Processors= 0.10 Desired Processors= 0.50 Maximum...

8. AIX

installing aix 5.2 on p520

hello everybody. Has anyone tried to install aix 5.2 on p520 machines. I've been trying but in the installation menu it says, "no disk found". I've used the same CD on a different 520 server and its working fine on it. Can anyone help, please?

9. AIX

connecting to service processor on 44P 170

I dont have an ascii terminal to hook upto this thing, trying to use my laptop but it doesnt seem to want to communicate, is there a special cable i should be using for this?

10. HP-UX

Service processor not responding

I am receiving messages from HP-UX Server "The operating system is unable to communicate with the service processor. The support bus which connects the system processors, the service processor and the Power Monitor or Platform Monitor may have become hung ". I need help in the following:...

LEARN ABOUT PHP

faxstate

FAXSTATE(8)						      System Manager's Manual						       FAXSTATE(8)

NAME

       faxstate - control ``modem state'' of a device used by HylaFAX

SYNOPSIS

       /usr/sbin/faxstate [ -q queue-dir ] [ -s state ] [ -n ] modem

DESCRIPTION

       faxstate  sends	a  message  to	the  HylaFAX  faxgetty(8) process servicing modem telling it to use the specified state when notifying the
       HylaFAX scheduler that a modem is ready and available for use.  This is useful for controlling outbound	use  of  a  modem;  by	marking  a
       modem's state as busy or down the HylaFAX scheduler will not assign any outbound jobs to the modem.

       The  specified  modem can either be the name (typically the last component of the terminal port the modem is attached to), or the full name
       of the associated FIFO named pipe file, e.g. ``FIFO.ttym2''.

       If the -n option, faxstate emulates what faxgetty would do; sending a message directly to the faxq  process  marking  the  specified  modem
       down,  busy,  or  ready.   This	interface is useful for send-only environments in which faxgetty processes are not used.  Note that modems
       manipulated in this way must previously have been configured with the faxmodem(8) program.

OPTIONS

       The following options are supported:

       -n	 Contact faxq directly instead of faxgetty.

       -q dir	 Use a spooling area other than /var/spool/hylafax.

       -s	 Specify the state to send the faxq process each time the modem becomes ready for use; one of ``busy'', ``down'',  and	``ready''.
		 The default state to use is ready.

FILES

       Consult hylafax-server(5) for a complete discussion of the structure and content of the spooling area.

SEE ALSO

       hylafax-server(5), faxgetty(8)

								   July 17, 1995						       FAXSTATE(8)

AIX