12-27-2005
use command "print_manifest" to get the information about the system
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello, i have to activate a network interface. for HPUX1100 i can command ifconfig lanx plumb.
Why doesent it works under HPUX10.20?
How can i realise it?
thanks for your help!:) (2 Replies)
Discussion started by: ortsvorsteher
2 Replies
2. HP-UX
Hi guys,
Need a favour or information on how to get it done in configuring a HPUX-11i box?I need the commands which is needed to configure the box...The pdf's in HP site is too much to look at.Is there any advice from u guys on how could i settle this problem? (7 Replies)
Discussion started by: giriplug
7 Replies
3. AIX
Hi All,
Needed commands to find Monitor , chassis & keyboard related information on AIX.
Please please please help.
Thanks
VK (2 Replies)
Discussion started by: Veenak15
2 Replies
4. HP-UX
Hi All
Please somebody send me list of admin commands used for HPUX.
Thanks
Sunanda (2 Replies)
Discussion started by: sunanda
2 Replies
5. Solaris
Hi all
Got another strange one. If I try to enquire about the hardware, the command hangs implying Ive got a hardware issue. So, if I execute :-
iostat -en
sysdef - ( stops at the devices part )
format
cfgadm -al
Anything that searches the devices, then the command hangs.
... (4 Replies)
Discussion started by: sbk1972
4 Replies
6. HP-UX
I am new for HPUX OS and want to pursue my career in HPUX Administration.
I could not able to get following information from HP.com site, that why I need an assistance to know that - can I install HPUX 11i V3 OS on old HP B2000 & B1000 workstations (these workstation are 4 to 5 year old) or not,... (5 Replies)
Discussion started by: girish.batra
5 Replies
7. Solaris
Hi guru
I want to know which company's hardware is more stable means in term of H/W faults or replacement, in case of IBM (AIX), HP (HPUX) & SUN MICROSYSTEM (Solaris) & which order also, if we go through more stable to less stable system.
Regards (1 Reply)
Discussion started by: girish.batra
1 Replies
8. Hardware
Are there any other useful hardware commands to get information about your hardware? Is there any information that can't be found with these commands?
cat /proc/cpuinfo
cat /proc/meminfo
dmesg
lspci
sudo dmidecode
cpuid | more
lspci -v | grep VGA
sudo lspci -v -s 00:02.0
sudo lspci -vvv... (12 Replies)
Discussion started by: cokedude
12 Replies
9. HP-UX
We would like to know a HP Utility or any Unix command that can give the exact status of PCI Gigabit Ethernet cable (lan cable) We had tried to execute
lanscan
ioscan -fnC lan
The status appears to be the same when the cable is plugged & unplugged and also when the lan is disabled &... (5 Replies)
Discussion started by: siva3492
5 Replies
10. HP-UX
I own a 1999 vintage HP Logic Analyzer that runs HPUX 10.20. It is a 9000/775/rock system similar to a Visualize C132L/160L system.
I'm attempting, mostly for the fun of it, to upgrade the existing slow 5MB/s-only SCSI system, with a new-er PCI card. Of course drivers is my major concern. I'd... (2 Replies)
Discussion started by: KeithM
2 Replies
time(1) General Commands Manual time(1)
Name
time - time a command
Syntax
time command
/bin/time command
Description
The command lets the specified command execute and then outputs the amount of elapsed real time, the time spent in the operating system,
and the time spent in execution of the command. Times are reported in seconds and are written to standard error.
If you are using any shell except the C shell, you can give the command as shown on the first line of the Syntax section. If you are using
the C shell, you must use the command's full pathname as shown on the second line of the Syntax section. If you do not use the full path-
name, will execute its own built-in command that supplies additional information and uses a different output format.
The command can be used to cause a command to be timed no matter how much CPU time it takes. For example:
% /bin/time cp /etc/rc /usr/bill/rc
0.1 real 0.0 user 0.0 sys
% /bin/time nroff sample1 > sample1.nroff
3.6 real 2.4 user 1.2 sys
This example indicates that the command used negligible amounts of user and system time and had an elapsed time of 1/10 second (0.1). The
command used 2.4 seconds of user time and 1.2 seconds of system time, and required 3.6 seconds of elapsed time.
Restrictions
Times are measured to an accuracy of 1/10 second. Thus, the sum of the user and system times can be larger than the elapsed time.
See Also
csh(1)
time(1)