12-27-2005
HI Veena,
can u tell me which server your working on?? i mean what class?
there is nothing called BIOS in HP-UX HP9000 servers, ther is something called firmware ?? which u can find at GSP/MP console prompt.
let me know whats the exact info u need ??
REgards
govinda.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello, i have to activate a network interface. for HPUX1100 i can command ifconfig lanx plumb.
Why doesent it works under HPUX10.20?
How can i realise it?
thanks for your help!:) (2 Replies)
Discussion started by: ortsvorsteher
2 Replies
2. HP-UX
Hi guys,
Need a favour or information on how to get it done in configuring a HPUX-11i box?I need the commands which is needed to configure the box...The pdf's in HP site is too much to look at.Is there any advice from u guys on how could i settle this problem? (7 Replies)
Discussion started by: giriplug
7 Replies
3. AIX
Hi All,
Needed commands to find Monitor , chassis & keyboard related information on AIX.
Please please please help.
Thanks
VK (2 Replies)
Discussion started by: Veenak15
2 Replies
4. HP-UX
Hi All
Please somebody send me list of admin commands used for HPUX.
Thanks
Sunanda (2 Replies)
Discussion started by: sunanda
2 Replies
5. Solaris
Hi all
Got another strange one. If I try to enquire about the hardware, the command hangs implying Ive got a hardware issue. So, if I execute :-
iostat -en
sysdef - ( stops at the devices part )
format
cfgadm -al
Anything that searches the devices, then the command hangs.
... (4 Replies)
Discussion started by: sbk1972
4 Replies
6. HP-UX
I am new for HPUX OS and want to pursue my career in HPUX Administration.
I could not able to get following information from HP.com site, that why I need an assistance to know that - can I install HPUX 11i V3 OS on old HP B2000 & B1000 workstations (these workstation are 4 to 5 year old) or not,... (5 Replies)
Discussion started by: girish.batra
5 Replies
7. Solaris
Hi guru
I want to know which company's hardware is more stable means in term of H/W faults or replacement, in case of IBM (AIX), HP (HPUX) & SUN MICROSYSTEM (Solaris) & which order also, if we go through more stable to less stable system.
Regards (1 Reply)
Discussion started by: girish.batra
1 Replies
8. Hardware
Are there any other useful hardware commands to get information about your hardware? Is there any information that can't be found with these commands?
cat /proc/cpuinfo
cat /proc/meminfo
dmesg
lspci
sudo dmidecode
cpuid | more
lspci -v | grep VGA
sudo lspci -v -s 00:02.0
sudo lspci -vvv... (12 Replies)
Discussion started by: cokedude
12 Replies
9. HP-UX
We would like to know a HP Utility or any Unix command that can give the exact status of PCI Gigabit Ethernet cable (lan cable) We had tried to execute
lanscan
ioscan -fnC lan
The status appears to be the same when the cable is plugged & unplugged and also when the lan is disabled &... (5 Replies)
Discussion started by: siva3492
5 Replies
10. HP-UX
I own a 1999 vintage HP Logic Analyzer that runs HPUX 10.20. It is a 9000/775/rock system similar to a Visualize C132L/160L system.
I'm attempting, mostly for the fun of it, to upgrade the existing slow 5MB/s-only SCSI system, with a new-er PCI card. Of course drivers is my major concern. I'd... (2 Replies)
Discussion started by: KeithM
2 Replies
LEARN ABOUT OSF1
sys_attrs_bparm
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)