Hi,
I have broken my laptop hard drive so I would like to put it in an external box to backup my documents.
I have a doubt whether the interface of the hard disk is sata or ide.
Inside notes attached, is reported "controller SATA AHCI" but on the model section is given IDE hard disk
Hi experts,
I need to determine if I have 4GB free space on my UNix server? Is there a way that I can do it instead of executing df -k . in each folder?
Thanks for your help. (3 Replies)
:eek: I use this Solaris to run CMS a call acounting software package for my job. No one could run reports today because it said the this when you logged on
"The following file systems are low, and could adversely affect server performance:
File system /: 99%full"
Can some one please explain... (9 Replies)
Hi,
I can't make the network connection. The cable and hub should be fine since they are working on other systems. I've used 'mktcpip' as well as 'smit tcpip' to configure the interface, and was able to ping the system itself, but I can not ping the gateway - no response. After reboot, the IP... (1 Reply)
Hi,
I have a failed hard disk in my Sun Fire V240. Unfortunately it does not show up in 'cfgadm -al' or in the format command so I cannot unconfigure it and illuminate the blue light on the front to identify it. Is there any way of iluminating the blue lights on the other disks so I can at... (3 Replies)
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Good Evening,
2 years ago, I set up an Ubuntu file-server for a friend, who is a photograph amateur. Basically, the server offers a software RAID-5 that can be accessed remotely from a MAC. Unfortunately, I didn't labeled the hard drives (i.e. which physical drive corresponds to the /dev/sdX... (2 Replies)
Hello,
Currently we have a Oracle X4100 ( Solaris 10 ) server with disk failure. Originally our hardware team thought the disk can be hot-swap, when they stood in front of the server, none of the disk failure LED were on, so now we have no idea which disk is the bad one for replacement.
As... (2 Replies)
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
LEARN ABOUT DEBIAN
laptop_mode
LAPTOP_MODE(8) System Manager's Manual LAPTOP_MODE(8)NAME
/usr/sbin/laptop_mode - apply laptop mode settings
SYNOPSIS
/usr/sbin/laptop_mode [ cmd ] [ force ]
DESCRIPTION
This manual page documents briefly the /usr/sbin/laptop_mode command. laptop_mode is a program that applies the settings given in the
/etc/laptop-mode/laptop-mode.conf configuration file. The primary use is to control the laptop mode feature included in Linux kernels with
versions 2.6.6 and higher, and 2.4.23 and higher. This feature increases battery life by letting your hard drive spin down. This is
achieved by grouping disk write activity into "chunks" that are spaced at larger intervals than they normally would be. In addition to sup-
porting the Linux kernel's laptop mode feature, /usr/sbin/laptop_mode also supports various power saving modules which are configured
through configuration files in the /etc/laptop-mode/conf.d directory.
It is not recommended to call /usr/sbin/laptop_mode directly to start or stop laptop mode, except in hardware event handlers. To apply new
configuration settings from laptop-mode.conf, call the laptop-mode service init script with the reload parameter.
COMMANDS
Specify force as the second parameter to force laptop_mode to re-apply a state even if the computer is already in that state. These are the
values that are allowed for cmd :
auto Enable or disable laptop mode based on the current power state. Note that this will not do anything if the laptop-mode service
has not been started!
status Display a status report about everything that laptop_mode affects.
SEE ALSO laptop-mode.conf(8).
AUTHOR
This manual page was written by Bart Samwel (bart@samwel.tk) for the Debian system (but may be used by others). Permission is granted to
copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 any later version published by
the Free Software Foundation.
On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL.
LAPTOP_MODE(8)