12-04-2013
This User Gave Thanks to solaris_user For This Post:
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hello
i'm working on aix 5300-05-03 hacmp ver 5.4
well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!!
the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 0.0.2.0
my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
2. AIX
hello
i'm working on AIX 5300-05-03 P520 hacmp 5.4
when connection to the internet is going down , firewall down, my application work verey verey slowly!!! and on the sliffer output i'm got trys of my serevr to do convert from ipv4 ipv6 ( 0.0.2.0 and AAAAAAAA).
some one have an idea why... (1 Reply)
Discussion started by: ariec
1 Replies
3. Solaris
Hi folks, i hope you'll help me to configure my ipv6 tunnel.
First, i create my tunnel in:
Hurricane Electric Free IPv6 Tunnel Broker
My IP is 83.228.93.34
in HE:
------------------------
Server IPv4 address: 216.66.84.46
Server IPv6 address: 2001:470:1f14:16a::1/64
Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies
4. Shell Programming and Scripting
I have perl script that I use to check and ping a list of ip,
The problem is, I didnt understand how to ping ipv6 on perl,
Could I use Ping::External??And how could I get the ping result (reply or not)?
This is my code
#!/usr/bin/perl --
use Net::Ping;
use Data::Validate::IP;
use... (3 Replies)
Discussion started by: franzramadhan
3 Replies
5. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
6. Solaris
Hi
I am looking to have an NTP server that will support both ipv4 and ipv6 clients. Is there anything specific about the configuration that I should be looking at? (7 Replies)
Discussion started by: eeisken
7 Replies
7. Solaris
Hi
I am looking to set-up ISC DHCP to support ipv6, and to migrate my existing SUN DHCP ipv4 to ISC,
finding the ipv4 options for the SUN DHCP options was ok eg
TFTPsrvN = tftp-server-name
OptBootF = bootfile-name
However if I set up a DHCPv6 does anyone know what the equivalent... (1 Reply)
Discussion started by: eeisken
1 Replies
8. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT OSF1
ntp.drift
ntp.drift(4) Kernel Interfaces Manual ntp.drift(4)
NAME
ntp.drift - Network Time Protocol (NTP) drift file
DESCRIPTION
When the NTP daemon (xntpd) is first started, it computes the error in the intrinsic frequency of the clock on the computer it is running
on. This process usually takes about a day or two after the daemon is started to compute a good estimate of this (and it needs a good
estimate to synchronize closely to its server). Once the initial value is computed, it will change only by relatively small amounts during
the course of continued operation.
The driftfile declaration should always be included in the ntp.conf file. This provides xntpd with complete path name to a file in which
it can store the current value of the frequency error. That way, if the daemon is stopped and restarted, it can reinitialize itself to the
previous estimate without spending time recomputing the frequency estimate.
The ntp.drift file contains one line with the following format: freq_offset flag Specifies the nominal frequency offset. DO NOT modify
this field. Specifies the method used to improve system clock accuracy. Specifies that xntpd runs a Phase-Locked Loop (PLL) algorithm to
keep synchronized with other hosts. This is the default. Specifies the use of the PLL algorithm in the kernel. This requires the
NTP_TIME kernel option. After the option is configured in the kernel, edit the ntp.drift file and change the flag value to 1.
See System Administration for information on the NTP_TIME kernel option.
FILES
Conventional name of the drift file
RELATED INFORMATION
Commands: ntpdate(8), ntpq(8), xntpd(8), xntpdc(8)
Files: ntp.conf(4)
Network Administration, System Administration delim off
ntp.drift(4)