What do you mean by "a particular interface"? Do you have multiple interfaces?
The easy answer is to edit or create the file /etc/defaultrouter and insert the address of the default router (gateway). This file is ascii and editable and should contain just an ip address of the router and nothing else (first line of file, left justified). This change would be permanent.
Hi, I'm new to unix and have absolutely no experience with it. I am trying to change the network setting on the only computer on our network with SCO Unix. We switched ISP's and now have a new set of IP's. I can't for the life of me figure out how to go in and change these settings, please help.... (12 Replies)
How can I change the gateway address on my sco Openserver 5.0.6. A cisco firewall is recently installed but the gateway on the system is still pointing at the old one.
I want it to use the gateway address of the router.
Please help. Thanks (2 Replies)
how we can get the gateway address.
i know gethostname used for ipaddress
how we can get the system gateway address.
thank u inadvance,
sree (2 Replies)
Hello, I need to write a program which sets server's ip address, router, network mask. Program also should set if it is an internal or external ip. Maybe someone can help me ? Any information from u is very useful :b:
I stopped at .. :(
#!/bin/sh
A=`hostname -i`
echo "server ip address is $A"... (4 Replies)
Is there a command that can lookup ip address, subnet mask, gateway, and dns all at the same. I know ifconfig can lookup ip address and subnet mask. I know route -n can lookup gateway. Not sure about a dns command. So I hope there is a way to lookup ip address, subnet mask, gateway, and dns all at... (2 Replies)
Hi,
Using Redhat 6.1 with all the latest patches. I have the default gateway address but it never gets loaded. I have to add that manually? Not sure. Any idea. Is there any other place which I need to add?
/etc/sysconfig/network-scripts/ifcfg-em1
DEVICE="em1"... (2 Replies)
Hi all,
i have a rhel 6.2 with a default gateway.
This server is an Intranet office with no internet access.
DNS are already configured and it's possible to resolve my target.
My goal is to link my application (apache forward) only to http://mytarget.yyy through a new gateway (That does... (0 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT OPENDARWIN
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-dlnrv] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION -d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-m hoplimit
Specify maximum hoplimit.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
RETURN VALUES
The traceroute6 command will exit with 0 on success, and non-zero on errors.
SEE ALSO ping(8), ping6(8), traceroute(8)HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD May 17, 1998 BSD