Sponsored Content
Operating Systems Solaris Carrier Detection in Solaris 8 for Dial in and Null Modem Connections Post 302821297 by DGPickett on Friday 14th of June 2013 10:48:30 AM
Old 06-14-2013
Well, the loss of DSR or CTS or even effectively a break (long zero) might also be what is detected. An rs232 can be as little as three wires, SD, RD and ground, emulating a current loop connection. Does stty have other lead watchers you might turn on? Can you put a breakout box on and see what leads are live as senders or receivers, or just a volt-ohm-meter, as even receivers usually have voltage or resistance you can sense?
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Got connected with Modem but cannot dial Telephone no. to connect to host

Hello There, I configure my Modem as follow. Step1. # admintool & Then from Browse --> Serial Port i select tta port and Edit --> Modify From that i select Template : Modem:Dial Out Baud Rate: 9600 Ok Step 2 # tip /dev/cua/a connected (1 Reply)
Discussion started by: abidmalik
1 Replies

2. UNIX for Dummies Questions & Answers

Hyperterminal null modem connection to Solaris

I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up. I hooked up a null... (3 Replies)
Discussion started by: seethams
3 Replies

3. UNIX for Dummies Questions & Answers

Dial-Up Modem

Im using Kinternet with a Lucent modem on Suse 9.0 Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0 This is the log that Kinternet gives after trying to connect: SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux. Status... (0 Replies)
Discussion started by: Synbios
0 Replies

4. SCO

Dial-Out & Dial-In Connections in OpenServer 5.0.6.

Friends, I am facing a problem in connecting two SCO Openserver 5.0.6 servers through Dial-Up connectivity as is done in the case of two Windows PCs. Please help me out with the following problems: (a) How to configure the modem? (b) How to setup a Dial-In connection? (c) How to... (1 Reply)
Discussion started by: thecobolguy
1 Replies

5. Solaris

null modem for testing

hi all.. sorry for repeating the same question many times, i just set up a null modem, i am using this as reference : DB25 DB9 -- - 2 TD ---- 2 RD 3 RD ---- 3 TD 4 RTS ---- 8 CTS 5 CTS ---- 7 RTS 7 GND ---- 5 GND 6 DSR -+ +--- 4 DTR 8... (0 Replies)
Discussion started by: waterbear
0 Replies

6. Solaris

help me!!!! how configure modem dial up with smc in solaris 10

Dear All, i have problem during install modem dial up with smc in solaris 10. i can't find "login" because it's stop in _receive started transmit started. thanks for your attention. this is the list during i dial to this number : altconn called Device Type ACU wanted... (0 Replies)
Discussion started by: mr.ridho
0 Replies

7. IP Networking

modem detection

How to get information that where is my modem configured in /dev. I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies

8. UNIX for Advanced & Expert Users

Modem (dial up) connecton to Unix machine

Hello to all, I have one problem and hope you'll be able to help me. It's about connecting Windows PC machine to Unix machine via dial up through Hyper terminal. Connection was working in the past. In the meantime, windows machine is replaced (win XP) and unix machine stayed as is. So nothing is... (1 Reply)
Discussion started by: Mick
1 Replies

9. BSD

Carrier Detection in FreeBSD

Regarding carrier detection on FreeBSD 9.1 being run within Virtual Box: I used a usb-serial dongle which shows up as ttyu0 on the BSD machine. Carrier detection appears to work. When I establish a null modem connection I receive a login prompt. If I login, and then unplug and plug back the... (2 Replies)
Discussion started by: rstor
2 Replies
EVIDLE(3)								 1								 EVIDLE(3)

The EvIdle class

INTRODUCTION
EvIdle watchers trigger events when no other events of the same or higher priority are pending ( EvPrepare , EvCheck and other EvIdle watchers do not count as receiving events ). Thus, as long as the process is busy handling sockets or timeouts(or even signals) of the same or higher priority it will not be trig- gered. But when the process is in idle(or only lower-priority watchers are pending), the EvIdle watchers are being called once per event loop iteration - until stopped, that is, or the process receives more events and becomes busy again with higher priority stuff. Apart from keeping the process non-blocking(which is a useful on its own sometimes), EvIdle watchers are a good place to do "pseudo-back- ground processing" , or delay processing stuff to after the event loop has handled all outstanding events. The most noticeable effect is that as long as any idle watchers are active, the process will not block when waiting for new events. CLASS SYNOPSIS
EvIdle EvIdleextends EvWatcher Inherited properties o public$is_active o public$data o public$is_pending o public$priority Methods o public EvIdle::__construct (callable $callback, [mixed $data], [int $priority]) o finalpublicstatic object EvIdle::createStopped (string $callback, [mixed $data], [int $priority]) Inherited methods o public int EvWatcher::clear (void ) o abstractpublic EvWatcher::__construct (void ) o public void EvWatcher::feed (int $revents) o public EvLoop EvWatcher::getLoop (void ) o public void EvWatcher::invoke (int $revents) o public bool EvWatcher::keepalive ([bool $value]) o public void EvWatcher::setCallback (callable $callback) o public void EvWatcher::start (void ) o public void EvWatcher::stop (void ) PHP Documentation Group EVIDLE(3)
All times are GMT -4. The time now is 05:05 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy