06-13-2013
A null modem is two cable heads and some wires. You can force CD true all the time with wiring it to DTR on the other side (if the other side powers off, there is no carrier). Wiring plans vary. Similar rules apply to other leads. Wiring varies to simulate a half duplex switched carrier modem as opposed to a full duplex continuous carrier modem. With the right wiring, it should be a rock.
https://en.wikipedia.org/wiki/Null_modem Two DTE's, each pretending to be DCE to the other.
https://en.wikipedia.org/wiki/RS-232
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello There,
I configure my Modem as follow.
Step1.
# admintool &
Then from Browse --> Serial Port
i select tta port and Edit --> Modify
From that i select Template : Modem:Dial Out
Baud Rate: 9600
Ok
Step 2
# tip /dev/cua/a
connected (1 Reply)
Discussion started by: abidmalik
1 Replies
2. UNIX for Dummies Questions & Answers
I am new to Unix. I just got my SUN box from ebay with Solaris supposedly preloaded. The problem is I am unable to connect via Hyperterminal to Solaris, or more to the point, cannot tell if I have a successful connection and that solaris is the one not properly booted up.
I hooked up a null... (3 Replies)
Discussion started by: seethams
3 Replies
3. UNIX for Dummies Questions & Answers
Im using Kinternet with a Lucent modem on Suse 9.0
Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0
This is the log that Kinternet gives after trying to connect:
SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux.
Status... (0 Replies)
Discussion started by: Synbios
0 Replies
4. SCO
Friends,
I am facing a problem in connecting two SCO Openserver 5.0.6 servers through Dial-Up connectivity as is done in the case of two Windows PCs. Please help me out with the following problems:
(a) How to configure the modem?
(b) How to setup a Dial-In connection?
(c) How to... (1 Reply)
Discussion started by: thecobolguy
1 Replies
5. Solaris
hi all..
sorry for repeating the same question many times,
i just set up a null modem, i am using this as reference :
DB25 DB9
-- -
2 TD ---- 2 RD
3 RD ---- 3 TD
4 RTS ---- 8 CTS
5 CTS ---- 7 RTS
7 GND ---- 5 GND
6 DSR -+
+--- 4 DTR
8... (0 Replies)
Discussion started by: waterbear
0 Replies
6. Solaris
Dear All,
i have problem during install modem dial up with smc in solaris 10.
i can't find "login" because it's stop in _receive started transmit started.
thanks for your attention.
this is the list during i dial to this number :
altconn called
Device Type ACU wanted... (0 Replies)
Discussion started by: mr.ridho
0 Replies
7. IP Networking
How to get information that where is my modem configured in /dev.
I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies
8. UNIX for Advanced & Expert Users
Hello to all,
I have one problem and hope you'll be able to help me.
It's about connecting Windows PC machine to Unix machine via dial up through Hyper terminal.
Connection was working in the past. In the meantime, windows machine is replaced (win XP) and unix machine stayed as is. So nothing is... (1 Reply)
Discussion started by: Mick
1 Replies
9. BSD
Regarding carrier detection on FreeBSD 9.1 being run within Virtual Box:
I used a usb-serial dongle which shows up as ttyu0 on the BSD machine. Carrier detection appears to work. When I establish a null modem connection I receive a login prompt. If I login, and then unplug and plug back the... (2 Replies)
Discussion started by: rstor
2 Replies
LEARN ABOUT DEBIAN
bti-shrink-urls
BTI-SHRINK-URLS(1) bti-shrink-urls BTI-SHRINK-URLS(1)
NAME
bti-shrink-urls - convert URLs to a shorter form using a web service
SYNOPSIS
bti [--escaped] [--help] [URL]
DESCRIPTION
bti-shrink-urls converts URLs to a shorter form using a web service.
Currently http://2tu.us/ (default) and http://bit.ly / http://j.mp are supported.
OPTIONS
--escaped
Don't escape special characters in the URL any more, they are already percent encoded.
--help
Print help text.
URL
Specify the URL to be converted. If no URL is given bti-shrink-urls waits for input on stdin.
CONFIGURATION
bti-shrink-urls is configured by setting some values in ~/.bti:
shrink_host
Possible values: 2tu.us (default), bit.ly, j.mp
shrink_bitly_login
API login for bit.ly, j.mp, required if shrink_host is set to bit.ly or j.mp. See
https://code.google.com/p/bitly-api/wiki/ApiDocumentation
shrink_bitly_key
API key for bit.ly, j.mp, required if shrink_host is set to bit.ly or j.mp. See
https://code.google.com/p/bitly-api/wiki/ApiDocumentation
AUTHOR
Written by Bart Trojanowski bart@jukie.net.
COPYRIGHT AND LICENSE
Copyright (C) 2009 Bart Trojanowski bart@jukie.net.
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by
the Free Software Foundation version 2 of the License.
bti-shrink-urls March 2009 BTI-SHRINK-URLS(1)