03-15-2013
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
3. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX for Advanced & Expert Users
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Discussion started by: sadosan83
3 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
io::all::http
IO::All::HTTP(3pm) User Contributed Perl Documentation IO::All::HTTP(3pm)
NAME
IO::All::LWP - Extends IO::All to HTTP URLs
SYNOPSIS
use IO::All;
$content < io('http://example.org'); # GET webpage into scalar
io('http://example.org') > io('index.html'); # GET to file
"hello
" > io('http://example.org/index.html'); # PUT webpage
# two ways of getting a page with a password:
$content < io('http://me:secret@example.org');
$content < io('http://example.org')->user('me')->password('secret');
DESCRIPTION
This module extends IO::All for dealing with HTTP URLs. Note that you don't need to use it explicitly, as it is autoloaded by IO::All
whenever it sees something that looks like an HTTP URL.
The SYNOPSIS shows some simple typical examples, but there are many other interesting combinations with other IO::All features! For
example, you can get an HTTP URL and write the content to a socket, or to an FTP URL, of to a DBM file.
METHODS
This is a subclass of IO::All::LWP. The only new method is "http", which can be used to create a blank IO::All::HTTP object; or it can also
take an HTTP URL as a parameter. Note that in most cases it is simpler just to call io('http://example.com'), which calls the "http" method
automatically.
OPERATOR OVERLOADING
The same operators from IO::All may be used. < GETs an HTTP URL; > PUTs to an HTTP URL.
SEE ALSO
IO::All, IO::All::LWP, LWP.
AUTHORS
Ivan Tubert-Brohman <itub@cpan.org> and Brian Ingerson <ingy@cpan.org>
COPYRIGHT
Copyright (c) 2007. Ivan Tubert-Brohman and Brian Ingerson. All rights reserved.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
See <http://www.perl.com/perl/misc/Artistic.html>
perl v5.10.0 2007-03-29 IO::All::HTTP(3pm)