03-07-2013
I had asked
here
Quote:
is there any way to create shared virtual disk between two LPARs like how you can do it using Storage through Fiber on two servers ?
Trying to stimulate HACMP between two LPARs
and was
replied
Quote:
Originally Posted by
Vit0_Corleone
It's not possible .. you will get error like "resource busy" because it's already reserved for some Lpar
My question:
If I have one VIOS Machine running IVM and SAN Storage connected to it, is there a way to assign one shared disk on two LPARS
- I have one Fiber Card which is on VIOS IVM
- I will assign a disk from Storage to VIOS IVM
- from VIOS IVM how can i assign it to two LPARs for stimulating HACMP ?
thanks
10 More Discussions You Might Find Interesting
1. AIX
Hello,
I would like to know if anyone has faced this problem. Whenever there is a duplicate IP address, HACMP goes down infact HACMP ( PowerHA ) takes the whole system down.
Does anyone know how to solve this problem ? (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
3. AIX
I am planning for building a new database server using AIX 6.1 and Oracle 11.2 using ASM.
As i have learned starting with Oracle 11.2 ASM can only be used in conjunction with Clusterware, which is Oracles HA-software. As is the companies policy we do intend to use PowerHA as HA-solution instead... (1 Reply)
Discussion started by: bakunin
1 Replies
4. AIX
Hello!
I have this infraestructure:
- 1 POWER7 with single VIOS on Site A.
- 1 POWER6 with single VIOS on Site B.
- 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A.
- 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB.
- 1 Storage DS4700 on Site A.
- 1... (8 Replies)
Discussion started by: enzote
8 Replies
5. AIX
Hello AIX GURU's
Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server?
my questions are:
1.
Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar?
or
2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Hello,
AIX 6.1 TL7 SP6
POwerHA 6.1 SP10
I was experimenting with new hacmp build. It's 3-node cluster build on AIX 6.1 lpars. It contains Ethernet and diskhb networks. Shared vg disk is SAN disk. Two nodes see disk using vscsi, third node sees disk using npiv. Application is db2 server.
... (4 Replies)
Discussion started by: vilius
4 Replies
8. AIX
hello
ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415
work with dmx4 EMC storgae.
after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine :
hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies
9. AIX
I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp.
Please share me steps for adding vxvm diskgroup to hacmp. (6 Replies)
Discussion started by: sunnybee
6 Replies
10. AIX
Hi All,
As per the IBM upgrade/support matrix
IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix
we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ...
1 ) Bring down the cluster
2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LEARN ABOUT HPUX
vxsplitlines
vxsplitlines(1M) vxsplitlines(1M)
NAME
vxsplitlines - show disks with conflicting configuration copies in a cluster
SYNOPSIS
vxsplitlines [-g diskgroup] [-c daname]
DESCRIPTION
If you import portions of a disk group on different systems, this can lead to conflicting configuration copies on the disks of the disk
group.
If the configuration information in a disk group is ambiguous, it may not be possible for Veritas Volume Manager to determine which config-
uration copy is most up-to-date. (This is usually termed a serial split brain (SSB) condition when it occurs in a cluster.) You cannot
import a disk group in this state unless you specify which disk's configuration copy to use.
You can use the vxsplitlines command to see which disks in a disk group have conflicting configuration copies, and use this information
together with your knowledge of the history of the disk groups' usage to determine which configuration copy is most valid.
The output from vxsplitlines displays the vxdg commands that you can run to import the disk group using the available configuration copies.
The -o selectcp option of the vxdg import command is used to select the configuration copy to use for the import.
OPTIONS
-c daname Display the SSB IDs for each disk that are stored in the configuration copy on the disk specified by its disk access name.
Note: Although the SSB IDs for some disks may match, this does not necessarily mean that those disks' configuration copies have
recorded all the configuration changes. When viewed from some other configuration copies, the SSB IDs of the same disks may not
match.
-g diskgroup
Specifies the disk group. If a disk group is not specified, the default disk group is used as determined from the rules on the
vxdg(1M) manual page.
EXAMPLES
Display the disks on each side of the split in the disk group newdg:
vxsplitlines -g newdg
Display the SSB IDs stored in the configuration copy on disk c2t4d0:
vxsplitlines -g newdg -c c2t4d0
NOTES
The vxsplitlines is primarily intended to be used with private disk groups, but it also works with shared disk groups.
The version number of the disk group must be 110 or greater.
SEE ALSO
vxdg(1M)
Veritas Volume Manager Administrator's Guide
VxVM 5.0.31.1 24 Mar 2008 vxsplitlines(1M)