03-07-2013
I had asked
here
Quote:
is there any way to create shared virtual disk between two LPARs like how you can do it using Storage through Fiber on two servers ?
Trying to stimulate HACMP between two LPARs
and was
replied
Quote:
Originally Posted by
Vit0_Corleone
It's not possible .. you will get error like "resource busy" because it's already reserved for some Lpar
My question:
If I have one VIOS Machine running IVM and SAN Storage connected to it, is there a way to assign one shared disk on two LPARS
- I have one Fiber Card which is on VIOS IVM
- I will assign a disk from Storage to VIOS IVM
- from VIOS IVM how can i assign it to two LPARs for stimulating HACMP ?
thanks
10 More Discussions You Might Find Interesting
1. AIX
Hello,
I would like to know if anyone has faced this problem. Whenever there is a duplicate IP address, HACMP goes down infact HACMP ( PowerHA ) takes the whole system down.
Does anyone know how to solve this problem ? (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
3. AIX
I am planning for building a new database server using AIX 6.1 and Oracle 11.2 using ASM.
As i have learned starting with Oracle 11.2 ASM can only be used in conjunction with Clusterware, which is Oracles HA-software. As is the companies policy we do intend to use PowerHA as HA-solution instead... (1 Reply)
Discussion started by: bakunin
1 Replies
4. AIX
Hello!
I have this infraestructure:
- 1 POWER7 with single VIOS on Site A.
- 1 POWER6 with single VIOS on Site B.
- 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A.
- 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB.
- 1 Storage DS4700 on Site A.
- 1... (8 Replies)
Discussion started by: enzote
8 Replies
5. AIX
Hello AIX GURU's
Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server?
my questions are:
1.
Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar?
or
2. Can I just create virtual SCSI in VIO and map to Lpar and... (1 Reply)
Discussion started by: Vit0_Corleone
1 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Hello,
AIX 6.1 TL7 SP6
POwerHA 6.1 SP10
I was experimenting with new hacmp build. It's 3-node cluster build on AIX 6.1 lpars. It contains Ethernet and diskhb networks. Shared vg disk is SAN disk. Two nodes see disk using vscsi, third node sees disk using npiv. Application is db2 server.
... (4 Replies)
Discussion started by: vilius
4 Replies
8. AIX
hello
ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415
work with dmx4 EMC storgae.
after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine :
hdiskpower60 00c7f6b59fc60d9d caavg_private active... (1 Reply)
Discussion started by: ariec
1 Replies
9. AIX
I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp.
Please share me steps for adding vxvm diskgroup to hacmp. (6 Replies)
Discussion started by: sunnybee
6 Replies
10. AIX
Hi All,
As per the IBM upgrade/support matrix
IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix
we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ...
1 ) Bring down the cluster
2 )... (2 Replies)
Discussion started by: linux.amrit
2 Replies
LEARN ABOUT CENTOS
raw2hdf
raw2hdf(1) Emulators raw2hdf(1)
NAME
raw2hdf - Create an .hdf hard disk image from a raw data file
SYNOPSIS
raw2hdf rawfile hdffile
DESCRIPTION
raw2hdf converts a binary dump of a hard disk's data into an IDE disk image in .hdf format for use with Sinclair ZX Spectrum emulators.
OPTIONS
-v version
specifies the version of .hdf image to be created. Valid values are `1.0' for a version 1.0 file and `1.1' for a version 1.1 file.
Defaults to creating version 1.1 files.
rawfile
specifies a raw data file (or block device corresponding to an actual disk) to be converted.
hdffile
specifies the .hdf file to create.
NOTES
Since raw2hdf has no knowledge of the geometry of the disk from which the original image was taken (indeed, the input file need not origi-
nate from a real IDE disk at all), there is no guarantee that the information contained in the .hdf file header accurately represents the
original disk. However, it will attempt to construct a header that is consistent with the size of the image, to produce an .hdf file which
is functionally equivalent.
BUGS
None known.
SEE ALSO
fuse(1), fuse-utils(1), libspectrum(3)
The .hdf format specification, at
http://www.ramsoft.bbk.org/hdfform.html.
The comp.sys.sinclair Spectrum FAQ, at
http://www.worldofspectrum.org/faq/index.html.
AUTHOR
Matthew Westcott (matthew@west.co.tt).
Version 1.0.0 16th December, 2010 raw2hdf(1)