Hi,
IŽd like to have some opinions of waht settings we should take note before power down a server and move it to other facilities. Of course, the first thing is check the backups.
Thanks in advance. (1 Reply)
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Hi,I want connect my ASA 5510 firewall to a 3750 switch with RIP routing. Unfortunately,I am having issues passing the VPN subnet through rip to the 3750.I don't understand how the routing table is populated on the ASA. Any suggestions? (0 Replies)
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Hi all,
I need this as soon as possible to solve it or at least to find out what is the problem.
I have configured IPSec tunnels with Openswan and Cisco ASA, i have established a connection and the ping was fine, but after some time there is request time out from both sites. I don't have ASA... (0 Replies)
Discussion started by: ivancd
0 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD April 11, 1998 BSD