All,
I downloaded and installed the following net-snmp from the sourceforge.net website on a Solaris 9 server with the entire collection installed:
net-snmp-5.1.2-SunOS_5.9_sun4u.tar.gz
with no errors.
I attempt to run snmpget and I get the following error:
ld.so.1: snmpget: fatal:... (1 Reply)
hello
I am running solaris 8 sparc.
I installed net-snmp 5.4.1 (compiled it from tar file).
When I do snmpwalk from another server, I receive a partial list of OIDs then it stops and gives 'timeout. No response...'
another snmpwalk will directly timeouts.
I compiled again the binaries... (1 Reply)
Hi there,
I know this is a common question, but I have not found a satsifactory solution yet, so pardon me for posting similar questions.
My problem is the log /var/adm/messages is filling up with this entry every few minutes Please refer below.
Oct 4 21:39:46 host last message repeated 3... (5 Replies)
I'm unable to see any traps being sent from my Solaris 10 server using Net-snmp 5.4.2 Here is my snmp conf file. Please let me know if there are any syntax issues you might notice.
cat /etc/sma/snmp/snmpd.conf
###########################################################################
#
#... (1 Reply)
Hi,
I am trying to compile the source code for Net-SNMP-5.4.2.1 using the gcc compiler-3.4.6 and 3.4.3 but I am getting the follwoing error with perl enabled:
/bin/sh ../libtool --mode=link gcc -g -O2 -Usolaris2 -Dsolaris2=solaris2 -fno-strict-aliasing -pipe -Wdeclaration-after-statement... (2 Replies)
I am having trouble working with SNMP module with perl. I am trying to get SNMP version of target system. I use following code to get it however it resturns error as "Argument "v6.0.1" isn't numeric in numeric lt (<) at ./chk_env_upd.pl line 447."
Get load table
my $resultat =... (1 Reply)
Discussion started by: dynamax
1 Replies
LEARN ABOUT REDHAT
snmp-ups
snmp-ups(8) Network UPS Tools (NUT) snmp-ups(8)NAME
snmp-ups - Driver for RFC 1628 SNMP UPS equipment
NOTE
This man page only documents the hardware-specific features of the snmp-ups driver. For information about the core driver, see nutups-
drv(8).
SUPPORTED HARDWARE
Any UPS that is RFC 1628 (UPS MIB) compliant.
EXPERIMENTAL DRIVER
This driver has been tagged experimental and is not built by default.
REQUIREMENTS
This driver needs UCD SNMP, aka Net-SNMP installed to compile successfully. See http://www.net-snmp.org/ for more information.
On Red Hat 7.2, these packages are required:
ucd-snmp-devel-4.2.3-1, ucd-snmp-4.2.3-1, ucd-snmp-utils-4.2.3-1
You must install SNMP-UPS-MIB.txt in your MIBs directory - typically /usr/share/snmp/mibs/, but it may vary from system to system. You can
generate this from chapter 4 of RFC 1628 (see http://www.faqs.org).
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5):
community=name
Set community name (default = public)
snmp_version=version
Set SNMP version (default = v1, the other allowed value is v2c)
INSTALLATION
This driver is not built by default. You can build it by using "configure --with-drivers=snmp-ups" before calling make.
IMPLEMENTATION
The hostname of the UPS is specified with the "port" value in ups.conf, i.e.:
[snmp]
driver = snmp-ups
port = snmp-ups.example.com
community = public
snmp_version = v1
SUPPORTED VARIABLES
INFO_MFR UPS Manufacturer
INFO_MODEL UPS Model
INFO_FIRMREV Firmware/Software Version
INFO_STATUS OFF, OL, OB, BOOST, TRIM
INFO_BATTPCT Battery percentage
INFO_RUNTIME Predicted runtime on battery
INFO_BATTVOLT Battery Voltage
INFO_OUTVOLT Output Voltage
PLANNED SUPPORT
INFO_UTILITY Input Voltage
INFO_ACFREQ AC Frequency
INFO_UPSTEM UPS Temperature
INFO_LOADPCT Load Percentage
CMD_? Not determined
AUTHORS
Arnaud Quette, Hans Ekkehard Plesser
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/
NUT mailing list archives and information: http://lists.exploits.org/
Tue Oct 22 2002 snmp-ups(8)