01-29-2013
Without even little knowledge of your network infrastructure, I don't think it's possible to just hand out the solution.
Please let us know how your clients are connecting to the server. Is there any external firewall in between? Which port are you trying to open? When you say "site", do you mean "website"?
9 More Discussions You Might Find Interesting
1. Linux
Hi all,
I am running an oracle application server but the problem is that the default port it is using is 7777 and if i want to make it port 80 i have to run the server as root which something i do not want to do. If i understand well to run on a port under 1024 the application needs root... (1 Reply)
Discussion started by: staind_art
1 Replies
2. HP-UX
Dear All..
I have an HP-UX server, i need to access it through certain port to run application.., but i cant access it,
I can login as root by using other port
Can anyone give me any advice how to see the list of active port? and how to block / unblock it??
Thankyou in advance
... (1 Reply)
Discussion started by: grimanda
1 Replies
3. HP-UX
Dear Expects,
I am facing following discrepancies on our server.
a) When we give wrong root password three times in a row, the root account has been disabled.
b) System is forced to change the old password, whenever we tried to change the password of any of the OS user and for ROOT user... (2 Replies)
Discussion started by: oracle_rajesh_k
2 Replies
4. IP Networking
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
5. UNIX for Dummies Questions & Answers
Hi Guys,
Some of the websites are blocked in my office. And I know the root password.
I tried to unblock those sites.. Checkedcd /etc/modprobe.d
$ cat blacklist.conf
#
# Listing a module here prevents the hotplug scripts from loading it.
# Usually that'd be so that some other driver will... (8 Replies)
Discussion started by: Adhi
8 Replies
6. IP Networking
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Discussion started by: ashokvpp
0 Replies
7. IP Networking
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Discussion started by: Ayaerlee
0 Replies
8. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
aseqnet(1) General Commands Manual aseqnet(1)
NAME
aseqnet - ALSA sequencer connectors over network
SYNOPSIS
aseqnet [remotehost]
DESCRIPTION
aseqnet is an ALSA sequencer client which sends and receives event packets over network. Suppose two hosts connected by network, hostA as
a server and hostB as a client. The ALSA sequencer system must be running on both hosts. For creating the server port, run the following
on hostA:
hostA% aseqnet
sequencer opened: 128:0
Then a user client 128 with port 0 was opened on hostA. (The client number may vary.) For creating the (network-)client port, run aseqnet
with the hostname of the server:
hostB% aseqnet hostA
sequencer opened: 132:0
Now all events sent to hostA:128:0 are transferred to hostB:132:0, and vice versa.
The ports created by aseqnet can be connected arbitrary to other sequencer ports via aconnect(1). For example, to connect hostB:132:0 to a
MIDI output device 65:0:
hostB% aconnect 132:0 65:0
Then events to hostA:128:0 will be delivered to hostB:65:0. The following command plays MIDI on hostB.
hostA% pmidi -p 128:0 foo.mid
The multiple clients may exist simultaneously. If hostC is connected as a client to hostA, events from from hostA are sent to all con-
nected network clients, i.e. hostB and hostC. However, only one connection is allowed from a client to a server.
To disconnect network, stop all clients before server by ctrl-C or sending signal to them. The server will automatically quit.
OPTIONS
-p port
Specify the TCP port number or TCP service name.
-s addr
Subscribe to the given address for read automatically.
-d addr
Subscribe to the given address for write automatically.
-v Verbose mode.
SEE ALSO
aconnect(1), pmidi(1)
AUTHOR
Takashi Iwai <tiwai@suse.de>.
January 1, 2000 aseqnet(1)