Remove anet from zone configuration and then try add network interface explicity. You must have unused network interface in your LDOM. I assume that net1 is not used in your LDOM, so you can use it in your zone.
Hi Folks,
I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level.
Can the same be done with Guest LDoms while remaining at the control LDOM level?
... (4 Replies)
Hi,
There is LDOM Guest where I need to expand /u02 file systems on it.
It is residing on a Solaris 11 Hypervisor (Primary Domain).
The storage is expanded on vdisk presented to Hypervisor.
I need steps to expand the /u02 on LDOM Guest. (2 Replies)
T4-2 issues meant replacing motherboard.
I thought the ldom config was automatically saved? Got the oracle document here.
At the moment, unable to get ldoms back - here is the output from a few commands:-
ldm list
NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME... (4 Replies)
Need assitance in troubleshooting steps . Below is the issue
I have LDOM which has 4 zones on it . One zone logging into the server takes 13sec where as other zones are quick .
Troubleshooting steps which I did
- Checked /var/tmp . Not many files
- We have LDAP but thought that wouldnt be... (7 Replies)
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
hello to everyone. im new member here.
i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain.
I want to modify a parameter in inittab of the guest domain because start guest domain give me problems... (2 Replies)
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Discussion started by: Michele31416
7 Replies
LEARN ABOUT SUNOS
root_archive
root_archive(1M)root_archive(1M)NAME
root_archive - manage bootable miniroot archives
SYNOPSIS
/boot/solaris/bin/root_archive pack archive root
/boot/solaris/bin/root_archive unpack archive root
/boot/solaris/bin/root_archive packmedia solaris_image root
/boot/solaris/bin/root_archive unpackmedia solaris_image root
The root_archive utility is used to manage bootable miniroot archives and is currently only available on platforms. The utility can pack
and unpack boot/root archives in both ufs and hsfs (iso9660) format. It will always generate ufs archives.
root_archive also uses the lofi file driver to export a file as a block device (see lofi(7D)) and mount to mount or unmount file systems
and remote resources (see mount(1M)). root_archive requires the same privileges that are needed to run these commands.
SUBCOMMANDS
The root_archive command has the following subcommands:
pack archive root
Pack from the image found under the root directory to the archive.
unpack archive root
Unpack from the archive to an unpacked image under the root directory.
packmedia solaris_image root
Pack the solaris image to the root directory.
unpackmedia solaris_image root
Unpack the solaris image from the root directory.
For packmedia and unpackmedia, other items that do not go into the ramdisk image are copied or uncopied (see cpio(1)) as well. Specifi-
cally, this includes all the packaging databases needed for pkgadd and the other packaging utilities to succeed which are not used in the
running and hence pruned to conserve memory.
EXAMPLES
Example 1: Unpacking the Solaris x86 install image
The following command unpacks the current Solaris image from the root directory:
# root_archive unpackmedia
/export/nv/solarisdvd.nvx_dvd/latest /export/Boot
Where /export/nv/solarisdvd.nvx_dvd/latest represents a path to a Solaris x86 install image and /export/Boot is a directory that will be
purged or created, as necessary.
Example 2: Packing the Solaris x86 install image
The following command packs the current Solaris image to the root directory:
# root_archive packmedia
/export/nv/solarisdvd.nvx_dvd/latest /export/Boot
The following exit values are returned:
0
The command completed successfully.
1
The command exited due to an error.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Stable |
+-----------------------------+-----------------------------+
cpio(1), bootadm(1M), mount(1M), attributes(5), lofi(7D)
26 Sep 2005 root_archive(1M)