01-25-2013
Finding speed of NIC Card
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out?
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
3. Solaris
Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps?
Thanks! (1 Reply)
Discussion started by: FredSmith
1 Replies
4. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
5. UNIX for Dummies Questions & Answers
hai this is nagesh
when i was doing practical , i find some dought.
iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me (4 Replies)
Discussion started by: nag.mi2000
4 Replies
6. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
7. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
8. Solaris
how can we change the nic card speed
please explain through commands & steps ????
and i want to change NIC speed 100 --1000Mbps
and what is full & half duplex gives
thanks in advance (6 Replies)
Discussion started by: wkbn86
6 Replies
9. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
10. Solaris
Hi,
I have few Solaris (9 and 10) servers, whose consoles are running on 10 MBPs. Now, Network team is changing their switch, which doesn't support 10 MBPs and we need to check if console all of those servers will support 100MBPs or more.
Is there any way to check supported (or maximum supported)... (7 Replies)
Discussion started by: solaris_1977
7 Replies
ttt(1) net ttt(1)
NAME
ttt - Tele Traffic Tapper - a standalone program for local, real-time, graphical traffic-monitoring.
SYNTAX
ttt [-interface device] [-interval ms] [-dumpfile file [-speed N]] [-yscale (K|M|n)]
DESCRIPTION
ttt is the standalone traffic monitor program in the ttt program suite. It displays trafic-data of a local interface.
To run ttt, you must be "root" on most systems since only root is allowed to access the network filter device.
The ttt program suite is yet another descendant of tcpdump but it is capable of real-time, graphical, local and remote traffic-monitoring.
It won't replace tcpdump, rather, it helps you find out what to look into with tcpdump.
OPTIONS
-interface device
specifies the interface for packet capture. If not specified, the default interface is chosen.
-interval ms
Sets the interval in Milliseconds. If omitted, a interval of 1000 msec. is used as default.
-dumpfile file [-speed N]
use a dumpfile (produced by "tcpdump -w") as input. The speed option specifies the acceleration factor of the replay speed.
-yscale ('K'|'M'|n)
change the scale of y-axis. 'K' and 'M' represent 1000 and 1000000 respectively.
EXAMPLES
To run this program the standard way type:
ttt
To listen only on interface eth0:
ttt -interface eth0
AUTHORS
ttt was written by Kenjiro Cho < kjc@csl.sony.co.jp>.
This manual page was written by Thomas Scheffczyk <thomas.scheffczyk@verwaltung.uni-mainz.de>, for the Debian GNU/Linux system (but may be
used by others).
SEE ALSO
tttview(1), tttprobe(1)
Kenjiro Cho 1.7 ttt(1)