01-02-2013
Thank you for writing a follow-up.
Moderator's Comments:
|
|
changed the thread title to SOLVED
|
|
bakunin
10 More Discussions You Might Find Interesting
1. AIX
When using PowerVM Express and IVM (no HMC) on a Power6 P520 , can I configure 2 LPARs in addition to a VIO server, or does the VIO Server count as one of the two LPAR's that PowerVM Express allows? (1 Reply)
Discussion started by: JodyTek
1 Replies
2. HP-UX
Please help me >
How to diag the external DVD-ROM drive issue whether it is working or not? on HP 9000 server rp7400
I needed to install HP 11i v1 using external DVD-ROM drive on HP 9000 server rp7400. While boot in CO> “search” command is not showing DVD-ROM device only showing all disks >... (0 Replies)
Discussion started by: tpuser
0 Replies
3. UNIX for Advanced & Expert Users
old clunker - rp74000
How to diag the external DVD-ROM drives issue whether it is working or not? on HP 9000 server rp7400
Please help me > I needed to install HP 11i v1 using external DVD-ROM drive on HP 9000 server rp7400. While boot in CO> “search” command is not showing DVD-ROM device... (1 Reply)
Discussion started by: tpuser
1 Replies
4. AIX
Hi everyone,
Sorry if this post is in the wrong place. I searched the forums for "IVM" and it turned up no results. Hopefully someone knows about this. My dilemma is that I have multiple IBM JS12 Express blades in our blade center, each running VIOS 2.1.0.10-FP-20.1 and hosting a couple LPARs. Out... (2 Replies)
Discussion started by: need2bageek
2 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. AIX
Hi,
When I try to login on my vios ivm website http://vios through the browser -- all three of them -- firefox , chrome , Internet Explorer , i get this error
http://vioserver/j_security_check
I have java installed on the machine from where i am trying to open up the IVM/VIOS webpage.
I... (2 Replies)
Discussion started by: filosophizer
2 Replies
7. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
8. AIX
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies
9. AIX
coming from this thread: https://www.unix.com/aix/211107-ibm-power-pseries-open-firmware-boot-vios-powervm-vet-code.html
PowerVM, formerly known as Advanced Power Virtualization (APV), is a chargeable feature of IBM POWER5, POWER6, POWER7, POWER8, and POWER9 servers and is required for support... (0 Replies)
Discussion started by: filosophizer
0 Replies
10. AIX
Hello,
After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )
i get this message
"I/O hosting requires a hosting partition - boot not permitted".
HMC was connected to the machine
then HMC was removed through ASMI
Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies
NETROM(4) Linux Programmer's Manual NETROM(4)
NAME
AF_NETROM - NET/ROM amateur packet radio protocol family
DESCRIPTION
NET/ROM is a protocol used extensively by radio amateurs. The Linux NET/ROM protocol family permits access to these protocols via the stan-
dard networking socket metaphor.
The NET/ROM protocol layer only supports connected mode. IP traffic may be stacked on top of NET/ROM frames using a non-standard extension
to the NET/ROM protocol.
The only mode of operation is connected mode which is the mode used for a socket of type SOCK_SEQPACKET (stream sockets are not available
in NET/ROM). This requires that the user ensures output data is suitably packetised, and that input data is read a packet at a time into a
buffer of suitable size.
NET/ROM addresses consist of 6 ascii characters and a number called the SSID. These are encoded into a sockaddr_ax25 structure which is
provided to the relevant system calls.
NET/ROM has some unusual properties. Notably in a multi-user system an AX.25 address is often associated with a user, and some users may
not have such an association. a set of ioctl calls are provided to manage an association table.
NET/ROM supports the following socket options for SOL_NETROM. NETROM_T1 is the T1 timer in 1/10ths of a second, NETROM_T2 is the T2 timer
in 1/10ths of a second. NETROM_N2, the retry counter is also configurable. There is no 'infinite retry' option supported however. It is
possible for an application to request that the NET/ROM layer return the NET/ROM header as well as the application data, this is done via
the NETROM_HDRINCL socket option.
SEE ALSO
call(1), socket(2), setsockopt(2), getsockopt(2), nrbroadcast(5), nrports(5), netromd(8), noderest(8), nodesave(8), nrparms(8).
AUTHOR
Jonathan Naylor G4KLX <g4klx@g4klx.demon.co.uk>
Linux 25 July 1996 NETROM(4)