Hi experts,
In my solaris system when i run the command df -h i got the below response.I have some confusion which i want to share with you guys.1)there are two SWAP file system shows are they same or different?2)if i want to count the total disk space should i take both the swap space or only... (2 Replies)
Hi all,
i just started started learning system programming and want to pursue a career in the sys prog area.
below is the program that use a fork() call.
i read in one of the tutorials that parent process and child process uses different address spaces and runs concurrently.
that meas each... (2 Replies)
Hi
I have checked the output of top command in which there is a difference shown between the swap of top command for a process with total swap memory usage of the top command.
Swap usage of process is higher than the total swap memory usage.
top - 18:28:21 up 7:13, 5 users, load... (2 Replies)
Hi,
i have done a blunder here, i increased the swap space on Xen5.6 server machine using below steps :-
1056 dd if=/dev/zero of=/root/myswapfile bs=1M count=1024
1057 ls -l /root/myswapfile
1058 chmod 600 /root/myswapfile
1059 mkswap /root/myswapfile
1060 swapon /root/myswapfile
... (1 Reply)
Hi Everyone,
I have added new Virtual disk to OS. The main point is I need to bring this whole Disk into LVM control, is it necessary to partition the disk using fdisk command and assign partition type as '8e', or can I directly add that disk into LVM, by running pvcreate command with out... (2 Replies)
Hi folks,
How can I scan newly attached network interfaces to server without reboot?
Is there any command or something to scan without reboot.
Thanks (5 Replies)
Hi,
I'm trying to migrate the content of disk 'A' to disk 'B', that they belong to the same vg 'data'_vg'. Whe using pvmove, I get the following error: 'device-mapper: suspend ioctl failed: Interrupted system call'. I put down the whole trace:
pvmove -v "source_disk" "sink_disk"
... (0 Replies)
Hi
I need to identify a newly attached LUN from NetApp on a linuxserver running uname -o
GNU/Linux
I have first run the df -h and got the following:
df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/vg_outsystemdb-lv_root
50G 2.7G 45G ... (3 Replies)
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Oflate we are finding a few servers experiencing severe slowness. What would be the commands that I need to try to postmortem the situation? (3 Replies)
Discussion started by: ggayathri
3 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)