i purchased, what was labeled as a 4-port fast ethernet sbus card from ebay.
i installed it in my ultra1, and it seems to be working fine. how can i determine if the card is infact a fast ethernet card vs. the standard ethernet 4-port card? (7 Replies)
I am trying to find a command to return the "link" speed of the networks installed on AIX.
ifconfig - gives me where the link is up and the duplex setting. I need to determine for example if the ethernet connection is 10, 100, 1000 Mbs or what the current speed is based on the network media... (3 Replies)
Hello,
I have a Supermicro server with a P4SCI mother board running Debian Sarge 3.1. This is the "dmidecode" output related to RAM info:
RAM speed information is incomplete.. "Current Speed: Unknown", is there anyway/soft to get the speed of installed RAM modules? thanks!!
Regards :)... (0 Replies)
Hi guys
I have a bunch of x4100's x4140's etc with solaris 10 update4 running on them but I suspect that when a lot of these boxes were originally built, the jumpstart process used an update2 miniroot, now as far as i understand it, the miniroot used at jumpstart is the miniroot that stays on... (1 Reply)
I analysed disk performance with blktrace and get some data:
read:
8,3 4 2141 2.882115217 3342 Q R 195732187 + 32
8,3 4 2142 2.882116411 3342 G R 195732187 + 32
8,3 4 2144 2.882117647 3342 I R 195732187 + 32
8,3 4 2145 ... (1 Reply)
Hello
I've got a server with multiple NICS. In a script I want to log the outbound interface. Is there an easy way I can do this so that the output looks something like this:
host(xxx.xxx.xxx.xxx): Opening connection to ...
Obviously, getting the host is simple with hostname. But how... (4 Replies)
Being a novice user to linux i m little unaware of how would i check disk read write speed.
One of my mate is suggesting to create a file using dd command and check how much time it takes to create a 30 gb file .
I think this has a little sense however i would also like to take your reviews... (5 Replies)
Hello all,
I have a question about what you think the best practice is to determine what region you are running on when you have a system setup with a DEV/TEST, QA, and PROD regions running the same scripts in all.
So, when you run in DEV, you have a different directory structure, and you... (4 Replies)
Discussion started by: Rediranch
4 Replies
LEARN ABOUT DEBIAN
sraw
SRAW(8) System Manager's Manual SRAW(8)NAME
sraw - benchmark raw scsi I/O performance under linux
SYNOPSIS
sraw [ -fiv6 ] scsi-device [ bstart [ bstep ] ]
DESCRIPTION
This program basically reads the specified scsi device and measures the throughput. Note that the filesystem *AND* the buffer cache are
bypassed by this code, this program was designed to benchmark the naked scsi drivers by themselves without the need to account for the
overhead of any other portion of the kernel. It also could be used to benchmark disk read throughput.
This program does a series of reads of the disk, of consecutive areas on the disk. The device is first queried to determine the sector
size for the device, and then the series of reads is begun. About 5.0 Mb is read from the device, and then the performance numbers are
reported. Note that since the buffer cache is completely bypassed, there is no need to be concerned about cache hits or anything.
Output of sraw is a set of lines, 4 numbers per line: blocksize, elapsed time, nblocks and throughput (in bytes per second).
scsi-device is either a block device (e.g. /dev/sda, /dev/scd0) or a generic SCSI device (e.g. /dev/sg0).
OPTIONS -f set FUA (Force Unit Access) bit during read. Data is then read from media instead of internal drive cache.
-i use legacy ioctl instead of new SG I/O layer (will not work on 2.6 kernel and block devices).
-v more verbose output.
-6 use 6-bytes instead of 10-bytes read command. In this case, only the first GB of data could be read from media.
bstart starting block to check different zones on ZBR discs
bstep factor for sequential stepping, default 1. Use 0 for reading always the same blocks (from cache)
ERRORS
sraw could issue input/output errors when reading too many blocks at the same time from a block device like /dev/sda. To get rid of them,
use /dev/sgN instead.
AUTHOR
sraw was first written by Eric Youngdale. Extensions (-v, -f, -6, SG IO, man page) were written by Eric Delaunay.
SEE ALSO sg_dd(8) from sg3-utils package.
AVAILABILITY
sraw is available at
ftp://tsx-11.mit.edu/pub/linux/ALPHA/scsi/
Nov 1993 SRAW(8)