03-14-2012
You need to get to a "ok" prompt somehow.
The machine is obviously configured to boot from the network. Are you sure that it has a hard drive in it?
to get into install mode you either attach a console keyboard and screen and then all output goes to vga, or you detach console keyboard and screen and use serial interface only (eg. vt100).
I don't know the Blade 150 very well but I'd say that if you had a Sun keyboard you could type STOP-A to interrupt it, or if you had a serial keyboard attached you could type Ctrl-Break.
I don't think that you've got the right kit to do either.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I would like to upgrade the memory in my Sun Blade 150 workstation. In reading through Sun's Blade 150 DIMM Installation Guide, it indicates that the memory must be "certified by Sun for the Sun Blade 150 system."
Does anyone know if any SDRAM, PC133 • CL=2 • Unbuffered • ECC • 133MHz • 3.3V ... (2 Replies)
Discussion started by: here2learn
2 Replies
2. UNIX for Dummies Questions & Answers
Hi, I am new to UNIX. I have a Sun Blade 150 worksation. I used a Dell monitor and Dell keyboard as input and output devices. However, workstation always told me that keyboard couldn't be found. I used Dell keyboard with USB and Dell keyboard with series connector. It all didn't work. Please help... (10 Replies)
Discussion started by: duke0001
10 Replies
3. Solaris
I'm not familiar with this particular machine and it's baffling me. For those that are familar with the workstation, allow me to paint a picture. If you were looking down on the machine (open) you would see the main board and then a riser board. On the left side of the riser board are jacks... (1 Reply)
Discussion started by: silversaleen68
1 Replies
4. Solaris
FYI noob to here and sun blades...
I have a sun blade 100 and I can't get the cdrom to work. if i try using vold that doesn't seem to work either...maybe i'm not using it correctly.
Upon boot you can open/close the cdrom and it runs but after i'm logged in it won't open and i can't access it... (2 Replies)
Discussion started by: shaun138
2 Replies
5. Solaris
We had to replace a hard drive in one of our Sun Blade 150s, but now it hangs during the Jumpstart. It will show 1 or 2 Timeout for ARP/RARP messages and then start the spinning numbers. It always stops at 2ae00 and just hangs there.
We have 1 combined jumpstart server and it is also our NIS+... (5 Replies)
Discussion started by: stottsja
5 Replies
6. Solaris
I have recently re-installed Solaris 10 on a Sun Blade 150 followed by a patch set (10_Recommended) dated 2011.12.05.
I have just noticed /bin/sun now returns false, rather than true. See below.
$ uname -a
SunOS myblade1 5.10 Generic_147440-07 sun4u sparc SUNW,Sun-Blade-100
$ /bin/sparc &&... (1 Reply)
Discussion started by: apmcd47
1 Replies
7. Solaris
Hello,
I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies
8. Solaris
Hi everybody,
I'm having big troubles in installing Solaris 8 on a Sun Blade 150.
Here are some system specs:
Sun Blade 150 (UltraSPARC-IIe 550MHz)
RAM: 256MB
OBP 4.10.6 2003/06/06 12:30
POST 2.0.1 2001/08/23 17:13
When I try to boot from Solaris 8 CD with boot cdrom or... (10 Replies)
Discussion started by: Vortigern
10 Replies
9. Solaris
hello
i have a forte gamma camera Philips device . and its a medical device. this medical device is came with sun blade 150 pc and pegasys is printed on the sun blade pc .the problem is when i switched the power on , the sun blade runs and a white screen appear with the information about the... (6 Replies)
Discussion started by: moh_abaloo
6 Replies
10. Solaris
hi:)
i can't boot my sun server by iso solaris 10 sparc dvd that i did download from oracle site.
my hardware is sun T5220.
i receive these after running boot cdrom -s :
can't read disk lable
can't open disk lable package
ERROR: boot-read fail
whould u help me?
Please use CODE... (1 Reply)
Discussion started by: Arefdel
1 Replies
LEARN ABOUT DEBIAN
setupcon
SETUPCON(1) Console-setup User's Manual SETUPCON(1)
NAME
setupcon - sets up the font and the keyboard on the console
SYNOPSIS
setupcon [OPTION]... [VARIANT]
DESCRIPTION
setupcon is a program for fast and easy setup of the font and the keyboard on the console. Most of the time you invoke setupcon without
arguments. The keyboard configuration is specified in ~/.keyboard or /etc/default/keyboard. The font configuration is specified in
~/.console-setup or /etc/default/console-setup. Consult keyboard(5) and console-setup(5) for instructions how to configure these two
files.
If you have to switch often between different encodings, keyboards or languages, you can prepare several alternative configuration files
for setupcon. Suppose that most of the time you will use Greek language with Greek keyboard layout, but sometimes you need to type in Ger-
man with German keyboard layout. In this situation you should customize the main configuration files (keyboard and console-setup) for
Greek. Create also alternative configuration files for German named keyboard.german and console-setup.german. Then in order to configure
the console for Greek you will simply run the command with no arguments: setupcon and in order to configure the console for German you will
use setupcon german.
OPTIONS
-v, --verbose
Be more verbose. Use this option if something goes wrong or while experimenting with the configuration files.
-k, --keyboard-only
Setup the keyboard only, do not setup the font.
-f, --font-only
Setup the font only, do not setup the keyboard.
--force
Do not check whether we are on the console. Notice that you can be forced to hard-reboot your computer if you run setupcon with
this option and the screen is controlled by a X server.
--save This option can be useful if you want to use setupcon early in the boot process while /usr is not yet mounted and the required data
are not available. This option will make setupcon copy the required files in /etc/console-setup/ in order to make them available
before /usr is mounted. If you use setupcon early in the boot process, then you should run it with this option after every change
of the console configuration.
--save-only
The same as --save, but does not setup the keyboard and the font. This option can be useful if you want to save the required files
while the screen is controlled by a X server.
-h, --help
Display usage information.
VARIANT
Specifies which configuration file to use. By default the configuration files of setupcon are named console-setup and keyboard but
if you use e.g. chukchi as VARIANT then the configuration files will be console-setup.chukchi and keyboard.chukchi. In this way
you can have easy access to several different configurations - for example one for the Chukchi language and another for the default
configuration.
FILES
~/.console-setup
~/.keyboard
/etc/default/console-setup
/etc/default/keyboard
/etc/default/console-setup.VARIANT
/etc/default/keyboard.VARIANT
/etc/console-setup/
SEE ALSO
keyboard(5), console-setup(5)
console-setup 2011-03-17 SETUPCON(1)