03-18-2011
Here is little info, hope it helps:
(1) how do I know what is the LUN ID.
-> Depands on the driver which you are using.
for example: if using linux native multipathing then "multipath -ll" will show you the Lun & their details.
If using, third party drivers related to SAN:
for example - Rdac/mpp from IBM then u can use mppUtil -a <storage name>, will show u all the details of Luns...
(3) how do I scan for new LUNs.
again if using linux native multipath then run "rescan-scsi-bus.sh" avaialbe from sg3_utils rpm.
If using third party, for example Rdac of IBM: run "mppBusScan" and it will detect the new LUNs.
Hope it helps....
~Titans~
This User Gave Thanks to titanic4u For This Post:
10 More Discussions You Might Find Interesting
1. Slackware
hi,
i m tryin to learn ldap.
but its not getting configured.
the error msg it shows is:
LDAP configure error: BDB/HDB : Berkeley DB version incompatibe.
The BDB version i have installed is bdb4.2.52 and the ldap version is openldap-2.3.12.
my machine is running on red hat linux 9.
Why... (1 Reply)
Discussion started by: mridula
1 Replies
2. UNIX for Advanced & Expert Users
Hi Gurus:)
I have to connect from a SunOS 5.10 to a 5.8 using sftp in BatchMode. For this, I have generated a Public-Key (ssh-keygen -b 1024 -P "" -t dsa) on the 5.10 and saved it in ~remote-user/.ssh/authorized-keys on the 5.8.
Then, running either one of ssh or sftp, it asks for the... (24 Replies)
Discussion started by: unilover
24 Replies
3. UNIX for Dummies Questions & Answers
Is there a way to find the raid type without restarting the machine?
I m using linux operating system. (3 Replies)
Discussion started by: pinga123
3 Replies
4. UNIX for Dummies Questions & Answers
What are the two ways the hardware clock can be configured under Linux?
Thanks (3 Replies)
Discussion started by: lemon_06
3 Replies
5. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
6. HP-UX
Following this thread :
https://www.unix.com/hp-ux/189023-solved-way-tell-printer-used-configured-print-queue.html
This is rwuerth's nice contribution!
I had a more complicated script written a long time ago to find out this information,
but after realizing due to VBE's post (thank you VBE)... (0 Replies)
Discussion started by: rwuerth
0 Replies
7. UNIX for Dummies Questions & Answers
Hi all,
I have an environment with Aix and Linux severs zoned to tape drives
I'd like to list HBAs WWN on my servers which are zoned to the drives.
Thanks (1 Reply)
Discussion started by: Sara_84
1 Replies
8. IP Networking
Hi have a solaris server with the following IP 192.168.0.85, but anybody can login in using 172.19.0.85, and the ifconfigcommand does not show the 172.19.05 .
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask... (6 Replies)
Discussion started by: fretagi
6 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
10. Debian
I have kali running on vbox as :-
/etc/network/interfaces
ifup eth0 gives me
tpcdump (0 Replies)
Discussion started by: lazerz
0 Replies
LEARN ABOUT DEBIAN
multipath
MULTIPATH(8) Linux Administrator's Manual MULTIPATH(8)
NAME
multipath - Device mapper target autoconfig
SYNOPSIS
multipath [-v verbosity] [-d] [-h|-l|-ll|-f|-t|-F-B] [-p failover|multibus|group_by_serial|group_by_prio|group_by_node_name] [device]
DESCRIPTION
multipath is used to detect multiple paths to devices for fail-over or performance reasons and coalesces them
OPTIONS
-v level
verbosity, print all paths and multipaths
0 no output
1 print the created or updated multipath names only, for use to feed other tools like kpartx
2 + print all info : detected paths, coalesced paths (ie multipaths) and device maps
-h print usage text
-d dry run, do not create or update devmaps
-l show the current multipath topology from information fetched in sysfs and the device mapper
-ll show the current multipath topology from all available information (sysfs, the device mapper, path checkers ...)
-f flush a multipath device map specified as parameter, if unused
-F flush all unused multipath device maps
-t print internal hardware table to stdout
-r force devmap reload
-B treat the bindings file as read only
-p policy
force new maps to use the specified policy:
failover 1 path per priority group
multibus all paths in 1 priority group
group_by_serial
1 priority group per serial
group_by_prio
1 priority group per priority value. Priorities are determined by callout programs specified as a global, per-con-
troller or per-multipath option in the configuration file
group_by_node_name
1 priority group per target node name. Target node names are fetched in /sys/class/fc_transport/target*/node_name.
Existing maps are not modified.
device update only the devmap the path pointed by device is in. device is in the /dev/sdb (as shown by udev in the $DEVNAME variable) or
major:minor format. device may alternatively be a multipath mapname
SEE ALSO
multipathd(8), multipath.conf(5), kpartx(8), udev(8), dmsetup(8) hotplug(8)
AUTHORS
multipath was developed by Christophe Varoqui, <christophe.varoqui@opensvc.com> and others.
July 2006 MULTIPATH(8)