Expect/telnet/testing tacacs on a cisco Post: 302474258

9 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

Perl telnet to cisco router and compare the ping ms

All Please help, i will telnet to router to obain the ping status and compare, if higher than normal latency, i will have further action.. if i do the telent and in perl script then .... e.g the result i obtain from the router will be =' Success rate is 100 percent (5/5), round-trip...

2. Shell Programming and Scripting

Webpage to Telnet via Perl and Expect: Telnet problem?

Somewhat long story: I have a simple Perl CGI script that uses Expect to Telnet to a device and grab some data, and then spits it back to Perl for display on the Webpage. This works for many devices I've tried, but one device just fails, it keeps rejecting the password on this device, only...

3. Shell Programming and Scripting

Need help with Expect script for Cisco IPS Sensors, Expect sleep and quoting

This Expect script provides expect with a list of IP addresses to Cisco IPS sensors and commands to configure Cisco IPS sensors. The user, password, IP addresses, prompt regex, etc. have been anonymized. In general this script will log into the sensors and send commands successfully but there are...

4. Shell Programming and Scripting

perl telnet issue with cisco

Hi Experts, I am using perl to telnet on cisco boxes. We have this stupid cisco node which does not support "terminal Length0" command. Since I am using Net::Telnet and capturing output with @output = $telnet->cmd('cmd'); Say @output = $telnet->cmd('show version'); Now problem...

5. Shell Programming and Scripting

Perl variables inside Net::Telnet::Cisco Module doesn't work

I am writing perl script to configure Cisco device but Variables inside Net::Telnet::Cisco Module doesn't work and passed to device without resolving. Please advise. here is a sample of script: use Net::Telnet::Cisco; $device = "10.14.199.1"; ($o1, $o2, $o3, $o4) = split(/\./,$device);...

6. Shell Programming and Scripting

Bash script failed with expect on cisco routers

Hi all, I use a bash script which use expect to connect throught ssh and run command on a cisco router. The ssh connection with expect work fine, but the first command on the cisco router failed, I try to run the command in error by hand and it work fine... :( the first part of the script...

7. Shell Programming and Scripting

Perl Telnet cisco routers

Hi all i have little problem finding solution about simple telnet script .... i have 250 routers and on some i have different password and on some they ask just for password no username. So for example 1,2,3 have username and password (user,password) 4, and 5 have different username and password...

8. Shell Programming and Scripting

Expect script to show cisco configs

I know there are better ways to do this. I prefer snmp. I do not have the proper perl modules loaded on the platorm. Snmp isnt loaded on the platform. Telnet is not an option. I need to write an expect script to pull cisco equipment configs. The following code is executed once I gain...

9. Shell Programming and Scripting

Cisco, 2 ssh logins for expect /bash

HI all i need to connect to about 900 cisco routers and switch to do some configs changes. the issue i am having is that half the devices have one set of username and password and the other half have another username and password. From expect or bash script i can ssh into a device and make...

LEARN ABOUT DEBIAN

wcat

WCAT(1) 							   User Commands							   WCAT(1)

NAME

       wcat - printout wtmp entries

SYNOPSIS

       wcat [-w wtmp|-] [-adX[3|4]] [-s start] [-e end] [-b H[:M[:S]]] [--help] [--version]

SYNOPSIS

       Wcat provides an easy way to recover trimmed information from wtmp binary files. This tool can be useful for scripts that need only partial
       information from them.

       Notice that wcat output is binary wtmp entries so if this information is printed out to a terminal or screen it might mess it up. A  better
       use of wcat would be: wcat | rawtmp -w -

OPTIONS

       -w wtmp|-
	      Read alternate wtmp file.

       -X[3]  Read tacacs 3.x wtmp format.

       -X4    Read tacacs 4.0 wtmp format.

       -d     Output time in MMM DD HH:MM:SS date format.

       -a     Print contents of ut_addr (if it exists) instead of ut_host.

       -s start
	      Display accounting info from `start'.

       -e end Display accounting info up to `end'.

       -b H:M:S
	      Show accounting info from the last few hours/minutes/seconds.

       --help Print this help message.

       --version
	      Print the version of rawtmp.

SEE ALSO

       sac(8), ac(1), last(1), rawtmp(1), wtmp(5), netdate(8L)

FILES

       /var/log/wtmp		      login database
       /usr/adm/radacct/.../detail    Radius accounting logs

AUTHOR

       The upstream author of wcat is Steve Baker (ice@mama.indstate.edu)

       This manpage was written by Javier Fernandez-Sanguino based on help2man for the Debian GNU/Linux distribution (but can be used by others).

wcat v1.0 (c) 2001 by Steve Baker				   January 2003 							   WCAT(1)