Hello All,
A number of UNIX platforms currently bundle clients for the NIS, NIS+, and LDAP services.
I'd like to know how to discover what naming services are available.
E.g., results :
=============================
URL:
service:naming-directory:nis://192.168.1.100/eng.wiz.com
... (0 Replies)
Cannot get my Sun Solaris servers to log into a Brocade 5100. All fiber has been connected correctly and all drivers and firmware are loaded and up to date according to EMCGrab report. Below is an output from server. Please Help:
HBA Port WWN: 2100001b321063c4
OS Device Name: /dev/cfg/c3... (2 Replies)
We have a Sun M5000 connecting to a Brocade SAN switch. I don't know the IP of the Brocade switch and don't want to use its serial port to get the info. How can I find the IP of the Brocade switch under Solaris 10? Snoop is not supported by Solaris multipathing. What other tools can I use to find... (6 Replies)
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
I'm attempting to write a script that will look into a directory, discover all unique names, create directories for their prefix names and place the files inside. I do this now one by one with a simple script but I'd like to automate the process.
The directory would contain something like: ... (6 Replies)
How many pps (packets per second) roughly can average server user maximum use?
I mean if its normal to have like 100 000 pps
a few VPS users there have around 100,000 - 900,000pps
there has been bans for DoS.
PS: how pps value can be discovered and how tracked to causing process?
thx (0 Replies)
Hello;
experienced with HPUX/Linux, but new to Solaris, in particular my newly inherited SunOS 5.10 and is in a san environment
I have access to a 20gb lun, how do I discover it (and is a reboot required)
when discovered how do I configure it as a whole disk mount point (1 Reply)
I have my Windows computer in network 192.168.1.0/24 plugged into one interface of my router.
I have another port on the router as network 192.168.168.0/24 where my nas is plugged in.
Now Windows doesn't discover my NAS automatically, of course. Anyone know what would be the most elegant way to... (2 Replies)
Discussion started by: awayand
2 Replies
LEARN ABOUT CENTOS
rescan-scsi-bus.sh
RESCAN-SCSI-BUS.SH(1) User Commands RESCAN-SCSI-BUS.SH(1)NAME
rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting
SYNOPSIS
rescan-scsi-bus.sh [options] [host [host ...]]
OPTIONS -a, --alltargets
scan all targets, not just currently existing [default: disabled]
-d enable debug [default: 0]
-l activates scanning for LUNs 0--7 [default: 0]
-L NUM activates scanning for LUNs 0--NUM [default: 0]
-w, --wide
scan for target device IDs 0--15 [default: 0--7]
-c enables scanning of channels 0 1 [default: 0 / all detected ones]
-r, --remove
enables removing of devices [default: disabled]
-f, --flush
flush failed multipath devices [default: disabled]
-i, --issue-lip
issue a FibreChannel LIP reset [default: disabled]
-u, --update
look for existing disks that have been remapped
-s, --resize
look for resized disks and reload associated multipath devices, if applicable
--forcerescan
rescan existing devices
--forceremove
remove and readd every device (DANGEROUS)
--nooptscan
don't stop looking for LUNs is 0 is not found
--color
use coloured prefixes OLD/NEW/DEL
--hosts=LIST
scan only host(s) in LIST
--channels=LIST
scan only channel(s) in LIST
--ids=LIST
scan only target ID(s) in LIST
--luns=LIST
scan only lun(s) in LIST
--sync, --nosync
issue a sync / no sync [default: sync if remove]
--attachpq3
tell kernel to attach sg to LUN 0 that reports PQ=3
--reportlun2
tell kernel to try REPORT_LUN even on SCSI2 devices
--largelun
tell kernel to support LUNs > 7 even on SCSI2 devs
--sparselun
tell kernel to support sparse LUN numbering
Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended).
LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.)
SEE ALSO
rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi
sg3_utils Homepage: http://sg.danny.cz/sg
rescan-scsi-bus.sh 1.57 leden 2014 RESCAN-SCSI-BUS.SH(1)