Problems with network card in SCO Post: 302381219

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

2. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But...

3. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of...

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and...

5. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice...

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated.

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks

8. SCO

network problems with sco

SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that. thanks

9. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks !

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101...

LEARN ABOUT DEBIAN

mfontset_lookup

mfontset_lookup(3m17n)						 The m17n Library					    mfontset_lookup(3m17n)

NAME

       mfontset_lookup - Lookup a fontset.

SYNOPSIS

       MPlist * mfontset_lookup (MFontset * fontset, MSymbol script, MSymbol language, MSymbol charset)

DESCRIPTION

       Lookup a fontset. The mfontset_lookup() function lookups fontset and returns a plist that describes the contents of fontset corresponding
       to the specified script, language, and charset.

       If script is Mt, keys of the returned plist are script name symbols for which some fonts are specified and values are NULL.

       If script is a script name symbol, the returned plist is decided by language.

       o If language is Mt, keys of the plist are language name symbols for which some fonts are specified and values are NULL. A key may be Mt
	 which means some fallback fonts are specified for the script.
       o If language is a language name symbol, the plist is a FONT-GROUP for the specified script and language.  FONT-GROUP is a plist whose keys
	 are FLT (FontLayoutTable) name symbols (Mt if no FLT is associated with the font) and values are pointers to MFont.
       o If language is Mnil, the plist is fallback FONT-GROUP for the script.
       If script is Mnil, the returned plist is decided as below.
       o If charset is Mt, keys of the returned plist are charset name symbols for which some fonts are specified and values are NULL.
       o If charset is a charset name symbol, the plist is a FONT-GROUP for the charset.
       o If charset is Mnil, the plist is a fallback FONT-GROUP.
RETURN VALUE

	   It returns a plist describing the contents of a fontset. The plist should be freed by m17n_object_unref().
COPYRIGHT

       Copyright (C) 2001 Information-technology Promotion Agency (IPA)
       Copyright (C) 2001-2011 National Institute of Advanced Industrial Science and Technology (AIST)
       Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License
       <http://www.gnu.org/licenses/fdl.html>.

Version 1.6.2							    12 Jan 2011 					    mfontset_lookup(3m17n)

10 More Discussions You Might Find Interesting

1. IP Networking

network card

Discussion started by: cparks

2. IP Networking

Network Card with SGI

Discussion started by: DPAI

3. UNIX for Advanced & Expert Users

Network Card Help

Discussion started by: The Fridgerator

4. UNIX for Dummies Questions & Answers

Network card and internet

Discussion started by: Gibbler