Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Problems with network card in SCO
Operating Systems SCO Problems with network card in SCO Post 302380984 by daniel_cie on Wednesday 16th of December 2009 08:34:47 PM
Old 12-16-2009
I had this equipment out of service, and worked correctly, but now I need to use it does not work. drivers are the same as used before, also values an bus device function.
the drivers are correct.

jgt: check the information, but that information does not show the server motherboard, it only shows that the pci card installed

TonyLawrence: yes, manually captured data.
captured the same values I had before but still not working

when I run:
# ifconfig-a
if there net0
# tcp start
/etc/slink: function "cenetb", command 2: open "/dev/net1": No such file or directory
ifconfig: ioctl ( SIOCGIFFLASS ): no such interface
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

3. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

5. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

8. SCO

network problems with sco

SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that. thanks (8 Replies)
Discussion started by: ajantha
8 Replies

9. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

LEARN ABOUT DEBIAN

gchem3d

GCHEM3D(1)						       gnome-chemistry-utils							GCHEM3D(1)

NAME

       gchem3d - a small chemical viewer application

SYNOPSIS

       gchem3d [OPTION(S)...] [FILE...]

DESCRIPTION

       gchem3d is a small chemical viewer application, which can show several chemical file formats.

OPTIONS

       The following options are accepted:

       -b COLOR, --bgcolor=COLOR
	   Use the given color as background color.  COLOR can be one of "black" (default), "white", "#rrggbb" (don't forget to escape the "#"
	   character in the shell).

       -d MODEL, --display3d=MODEL
	   Choose how molecules are displayed.	MODEL can be one of "BallnStick" (default), "SpaceFill".

       -?, --help
	   Show application help options.

       --help-all, --help-*
	   Print all or just a group of help options. These options are not documented here. Instead see gtk-options(7) and gnome-options(7).

       -v, --version
	   Print gchem3d version information.

SEE ALSO

       gnome-options(7), gtk-options(7)

AUTHORS

       Jean Brefort <jean.brefort@normalesup.org>
	   Program author.

       Daniel Leidert <daniel.leidert@wgdd.de>
	   Manpage author.

COPYRIGHT

       Copyright (C) 2002-2007 Jean Brefort
       Copyright (C) 2004-2007 Daniel Leidert

       Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 or any
       later version published by the Free Software Foundation.

gcu 0.12				      $Date: 2009-03-19 10:53:47 +0100 (jeu. 19 mars 2009) $					GCHEM3D(1)
All times are GMT -4. The time now is 10:19 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy