12-16-2009
I had this equipment out of service, and worked correctly, but now I need to use it does not work. drivers are the same as used before, also values an bus device function.
the drivers are correct.
jgt: check the information, but that information does not show the server motherboard, it only shows that the pci card installed
TonyLawrence: yes, manually captured data.
captured the same values I had before but still not working
when I run:
# ifconfig-a
if there net0
# tcp start
/etc/slink: function "cenetb", command 2: open "/dev/net1": No such file or directory
ifconfig: ioctl ( SIOCGIFFLASS ): no such interface
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
3. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. SCO
Hi,
I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. SCO
SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that.
thanks (8 Replies)
Discussion started by: ajantha
8 Replies
9. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT MOJAVE
set_color
set_color(1) fish set_color(1)
NAME
set_color - set_color - set the terminal color
set_color - set the terminal color
Synopsis
set_color [-v --version] [-h --help] [-b --background COLOR] [COLOR]
Description
Change the foreground and/or background color of the terminal. COLOR is one of black, red, green, brown, yellow, blue, magenta, purple,
cyan, white and normal.
o -b, --background Set the background color
o -c, --print-colors Prints a list of all valid color names
o -h, --help Display help message and exit
o -o, --bold Set bold or extra bright mode
o -u, --underline Set underlined mode
o -v, --version Display version and exit
Calling set_color normal will set the terminal color to whatever is the default color of the terminal.
Some terminals use the --bold escape sequence to switch to a brighter color set. On such terminals, set_color white will result in a grey
font color, while set_color --bold white will result in a white font color.
Not all terminal emulators support all these features. This is not a bug in set_color but a missing feature in the terminal emulator.
set_color uses the terminfo database to look up how to change terminal colors on whatever terminal is in use. Some systems have old and
incomplete terminfo databases, and may lack color information for terminals that support it. Download and install the latest version of
ncurses and recompile fish against it in order to fix this issue.
Version 1.23.1 Sun Jan 8 2012 set_color(1)