12-16-2009
I had this equipment out of service, and worked correctly, but now I need to use it does not work. drivers are the same as used before, also values an bus device function.
the drivers are correct.
jgt: check the information, but that information does not show the server motherboard, it only shows that the pci card installed
TonyLawrence: yes, manually captured data.
captured the same values I had before but still not working
when I run:
# ifconfig-a
if there net0
# tcp start
/etc/slink: function "cenetb", command 2: open "/dev/net1": No such file or directory
ifconfig: ioctl ( SIOCGIFFLASS ): no such interface
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
3. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. SCO
Hi,
I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. SCO
SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that.
thanks (8 Replies)
Discussion started by: ajantha
8 Replies
9. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT DEBIAN
colorgccrc
COLORGCCRC(5) File Formats Manual COLORGCCRC(5)
NAME
colorgccrc - configuration file for colorgcc
DESCRIPTION
A colorgccrc configuration file is used to configure the highlighting of the compiler output from colorgcc.
SYNTAX
Each line consists of a keyword designating a configuration variable. The keyword is followed by `:' and then one or several values
(depending on the keyword). Lines beginning with a hash mark `#' are comments.
CONFIGURATION VARIABLES
g++ | gcc | c++ | cc | g77 | gcj | gnat | gpc
Specifies the paths to the compilers. Takes one value; a path to the compiler.
nocolor
Specifies what terminal types colorization should be disabled on. Takes one or several values, separated by whitespace.
srcColor
Specifies the highlighting attributes source-code should be given. Takes one or several color attributes. See the section COLOR
ATTRIBUTES for more information.
introColor
Specifies the highlighting attributes for normal compiler output. Takes one or several color attributes. See the section COLOR
ATTRIBUTES for more information.
warningFileNameColor | errorFileNameColor
Specifies the highlighting attributes for the filename in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
warningNumberColor | errorNumberColor
Specifies the highlighting attributes for the line-number in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
warningMessageColor | errorMessageColor
Specifies the highlighting attributes for the message-text in a warning or an error, respectively. Takes one or several color
attributes. See the section COLOR ATTRIBUTES for more information.
COLOR ATTRIBUTES
The following attributes are valid for highlighting.
clear, reset
bold, underline, underscore, blink, reverse, concealed
black, red, green, yellow, blue, magenta, cyan, white
on_black, on_red, on_green, on_yellow, on_blue, on_magenta, on_cyan, on_white
SEE ALSO
gcc(1), colorgcc(1)
HISTORY
Jan 15 2003: Initial version of this manual-page.
REPORTING BUGS
Report bugs to <jmoyers@geeks.com>
AUTHORS
Jamie Moyers <jmoyers@geeks.com> is the author of colorgcc.
This manual page was written by Joe Wreschnig <piman@sacredchao.net>, and modified by David Weinehall <tao@debian.org>, for the Debian
GNU/Linux system (but may be used by others).
COPYRIGHT
Copyright (C) 2003 Jamie Moyers
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU-
LAR PURPOSE.
Jan 15, 2003 COLORGCCRC(5)