12-16-2009
This sounds like you are entering values manually?
From
New to SCO Unix :
"When adding a pci Network card to SCO OSR5, the card should just "pop up" with netconfig - you shouldn't get a whole list of cards to choose from. If it does not, you probably do not have the right driver and should visit
ftp://ftp.sco.com/pub/drivers/ to get it. Also use "hw -r pci" to see what is actually installed."
Probably smarter to buy a card that SCO 5.0.5 DOES have drivers for. Unfortunately, that's going to be older versions - new cards may not work even if model number is the same.
Smarter still to move off SCO :-)
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
3. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. SCO
Hi,
I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. SCO
SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that.
thanks (8 Replies)
Discussion started by: ajantha
8 Replies
9. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT SUSE
uri::url
URI::URL(3) User Contributed Perl Documentation URI::URL(3)
NAME
URI::URL - Uniform Resource Locators
SYNOPSIS
$u1 = URI::URL->new($str, $base);
$u2 = $u1->abs;
DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to
be distributed with the libwww-perl library.
The following differences exist compared to the "URI" class interface:
o The URI::URL module exports the url() function as an alternate constructor interface.
o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase".
o The URI::URL->newlocal class method is the same as URI::file->new_abs.
o URI::URL::strict(1)
o $url->print_on method
o $url->crack method
o $url->full_path: same as ($uri->abs_path || "/")
o $url->netloc: same as $uri->authority
o $url->epath, $url->equery: same as $uri->path, $uri->query
o $url->path and $url->query pass unescaped strings.
o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters)
o $url->params and $url->eparams methods
o $url->base method. See URI::WithBase.
o $url->abs and $url->rel have an optional $base argument. See URI::WithBase.
o $url->frag: same as $uri->fragment
o $url->keywords: same as $uri->query_keywords
o $url->localpath and friends map to $uri->file.
o $url->address and $url->encoded822addr: same as $uri->to for mailto URI
o $url->groupart method for news URI
o $url->article: same as $uri->message
SEE ALSO
URI, URI::WithBase
COPYRIGHT
Copyright 1998-2000 Gisle Aas.
perl v5.12.1 2008-04-04 URI::URL(3)