12-16-2009
Problems with network card in SCO
hello, i am new to unix and need support</SPAN></SPAN>
</SPAN></SPAN>The problem is:
I have a SCO 5.0.5 server, and has no local network access, I think my problem are the drivers for network card.
my network card is Kingston EtheRx PCI Fast Ethernet Adapter KNE120TX and already installed the drivers, but when I run:
# hwconfig-h the result that describes the network card is:
ktcHT 0xd400-0xd41f - - Kingston Et ....... NOT FOUND [KNE120TX]
reinstall the drivers and the network connection, but does not work
when setting up the network connection, save with default values:
Bus = 0
Device = 0
Function = 0
this can cause any conflict?
if this is wrong, what are the correct values?
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
3. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. SCO
Hi,
I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. SCO
SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that.
thanks (8 Replies)
Discussion started by: ajantha
8 Replies
9. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT DEBIAN
mdbfontsize
mdbFontSize(5) The m17n Library mdbFontSize(5)
NAME
mdbFontSize - Font Size
DESCRIPTION
In some case, a font contains incorrect information about its size (typically in the case of a hacked TrueType font), which results in a
bad text layout when such a font is used in combination with the other fonts. To overcome this problem, the m17n library loads information
about font-size adjustment from the m17n database by the tags <font, resize>. The data is loaded as a plist of this format.
FONT-SIZE-ADJUSTMENT ::= PER-FONT *
PER-FONT ::= '(' FONT-SPEC ADJUST-RATIO ')'
FONT-SPEC ::=
'(' [ FOUNDRY FAMILY
[ WEIGHT [ STYLE [ STRETCH [ ADSTYLE ]]]]]
REGISTRY ')'
ADJUST-RATIO ::= INTEGER
FONT-SPEC is to specify properties of a font. FOUNDRY to REGISTRY are symbols corresponding to Mfoundry to Mregistry property of a font.
See m17nFont for the meaning of each property.
ADJUST-RATIO is an integer number specifying by percentage how much the font-size must be adjusted. For instance, this PER-FONT:
((devanagari-cdac) 150)
instructs the font handler of the m17n library to open a font of 1.5 times bigger than a requested size on opening a font whose registry is
'devanagari-cdac'.
COPYRIGHT
Copyright (C) 2001 Information-technology Promotion Agency (IPA)
Copyright (C) 2001-2011 National Institute of Advanced Industrial Science and Technology (AIST)
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License
<http://www.gnu.org/licenses/fdl.html>.
Version 1.6.2 12 Jan 2011 mdbFontSize(5)