09-24-2009
there are three disk they are
" Segate cheetah Model no: ST318406LC ultra3 SCSI 10k 18GB "
three disk are same disk
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. Solaris
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Discussion started by: sunnyd76
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT HPUX
diskinfo
diskinfo(1M) diskinfo(1M)
NAME
diskinfo - describe characteristics of a disk device
SYNOPSIS
character_devicefile
DESCRIPTION
The command determines whether the character special file named by character_devicefile is associated with a SCSI or floppy disk drive. If
so, summarizes the disk's characteristics.
The command displays information about the following characteristics of disk drives:
Vendor name Manufacturer of the drive (SCSI only)
Product ID Product identification number or ASCII name
Type Floppy or SCSI classification for the device
Disk Size of disk specified in bytes
Sector Specified as bytes per sector
Both the size of disk and bytes per sector represent formatted media.
Options
The command recognizes the following options:
Return the size of the disk in 1024-byte sectors.
Display a verbose summary of all of the information
available from the device. For floppy drives, this option has no effect.
SCSI disk devices return the following:
Vendor and product ID
Device type
Size (in bytes and in logical blocks)
Bytes per sector
Revision level
SCSI conformance level data
DIAGNOSTICS
Most of the diagnostic messages from are self-explanatory. However, one diagnostic message deserves further clarification. If the command
fails to access the lunpath corresponding to a given special file, it displays the following diagnostics data, which contains device iden-
tification and capability information:
device type 127 (unknown); device is inaccessible
iso ecma ansi rmb dtq resv rdf
WARNINGS
As of release 10.20 of HP-UX, certain IDE devices, CD-ROMs in particular, will respond to inquiries as if they were SCSI devices. There-
fore, the text "SCSI describe" in the output of the command does not definitively mean that the disk is in fact a SCSI drive (especially in
the case of CD-ROMs). Use to check which type of INTERFACE node, SCSI or IDE, the device's hardware path lies beneath, in order to defini-
tively determine a drive's interface.
DEPENDENCIES
General
The command supports floppy and HP SCSI disk devices.
SCSI Devices
The SCSI specification provides for a wide variety of device-dependent formats. For non-HP devices, may be unable to interpret all of the
data returned by the device. Refer to the drive operating manual accompanying the unit for more information.
AUTHOR
was developed by HP.
SEE ALSO
ioscan(1M), lsdev(1M), disktab(4), disk(7).
diskinfo(1M)