08-31-2009
Thanks for the quick reply, I will be sure to tag my code in the future.
My team does not have access to change the config on the switch (which is currently set to 100 full). In the mean time I have created a startup script in /etc/rc2.d/ to make the changes, though I would still like to know how to make it work with the conifg file.
10 More Discussions You Might Find Interesting
1. Solaris
Hi All
I've been having a lot of errors logged on the Cisco Catalyst (4000 series) which one of my Solaris servers is patched into. I have a feeling they are duplex related, but I'm a bit stuck as to how to confirm that.
How do I:
1. Check the duplex settings on my eri0 card?
2. Set the... (3 Replies)
Discussion started by: saabir
3 Replies
2. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
3. HP-UX
Hi Folks,
I want the command to change the duplex settings of a HP-UX server.
Thanks in advance.
Sagar. (2 Replies)
Discussion started by: sag71155
2 Replies
4. Solaris
Hi there
We have a bit of a debate going here over what the prefered method is for setting 1000/Full on e1000g or nge interfaces is.
As you aware the Solaris configration files for nge and e1000g dont allow you to "fix" 1000/Full but instead allow you to set auto-negotiate to ON but only... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
5. UNIX for Advanced & Expert Users
I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5.
#ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Discussion started by: csreenivas
6 Replies
6. Infrastructure Monitoring
Hi,
In UNIX, it's very easy to find the duplex speed. But in Windows, is there a easy way to find the duplex speed? I can't go to over 100 servers to find this out, I was wondering if I run one command to do this?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
7. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
8. AIX
How to change Speed Duplex !
How to change Speed Duplex by command
chdev -P -l ent1 -a media_speed=1000_Full_Duplex
How to change Speed Duplex by Smitty .
smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
Discussion started by: ITHelper
0 Replies
9. AIX
VIO Server connected to switch port and running with half duplex speed on one of the shared ethernet adapter. We have verified at switch end and everythings looks good.
Other ethernet adapter in the VIO server are connected and running in Full duplex speed.
Please help me find why this shared... (4 Replies)
Discussion started by: mugunthanvh
4 Replies
10. Shell Programming and Scripting
So I have a server I am trying to set up a script to send a Wall message notifying of my eth0 nic being set to 100 half duplex instead of 100 full duplex.
I know I am trying to read from /etc/sysconfig/network/ifcfg-eth0 to pull the parameters
STARTMODE=onboot
BOOTPROTO=static... (6 Replies)
Discussion started by: lutador72
6 Replies
rc2(8) System Manager's Manual rc2(8)
NAME
rc2 - Run command script executed when entering a multiuser run level
SYNOPSIS
rc2
DESCRIPTION
The rc2 script contains run commands that enable initialization of the system to a multiuser state; run level 2. In addition to commands
listed within the script itself, rc2 contains instructions to run certain commands found in the /sbin/rc2.d directory. The script defines
the conditions under which the commands execute; some commands run if the system is booting, other commands execute if the system is chang-
ing run levels.
By convention, files in the /sbin/rc2.d directory begin with either the letter "K" or the letter "S" and are followed by a two-digit number
and a filename; for example: K00lpd S00savecore S25uucp
In general, the system starts commands that begin with the letter "S" and stops commands that begin with the letter "K." Commands that
begin with the letter "K" run only when the system is changing run levels from a higher to a lower level. Commands that begin with the
letter "S" run in all cases. The numbering of commands in the /sbin/rc2.d directory is important since the numbers are sorted and the com-
mands are run in ascending order. Files in the /sbin/rc2.d directory are normally links to files in the /etc/init.d directory.
An entry in the inittab file causes the system to execute the rc2 run commands, for example: s2:23:wait:/sbin/rc2 < /dev/console >
/dev/console 2>&1
The following operations are typical of those that result from executing the rc2 script and the commands located in the /sbin/rc2.d direc-
tory. The operation depends on which state the system is entering or exiting. Setting the time zone Checking the current run level Stop-
ping network services and daemons Starting (or stopping) system services and daemons Starting the cron daemon Setting up paging and dump
facilities Setting up uucp files
Setting the TIMEZONE variable is one of the first operations completed by the rc2 script. This action provides the default time zone for
subsequent commands.
FILES
Specifies the command path Specifies the directory of commands that correspond to the run level
RELATED INFORMATION
Commands: init(8), rc0(8), rc3(8) delim off
rc2(8)