I running HPUX 11.0,
Netscape gives me an error "Unable to locate Server" when using a www.something.com address.
If I use an IP address I get past the router and onto the Internet.
My workstation can get to the Router @ 192.168.0.1 and also it's local APACHE server.
I have DHCP enabled... (8 Replies)
i have just installed solaris 10 on a 60 gb hard drive. now im trying to install my nic driver but when i put in the floppy disk for the nic card it cant read it, so then i found that i have to mount the floppy drive and i tried putting in the mount command but i dont know where to mount it and if... (38 Replies)
Hi I installed solaris developer edition 1/08 today.I want to connect to Broadband internet through my ADSL 2+ Modem/Router with a username and password.
plz help in this case,I am new to sun solaris:confused:
the modem itself is a router it worked well on ubuntu and red hat (3 Replies)
HI,
Am using GPRS ( MOB # 3230 ) internet connection in windows
Hw to use internet r connect in linux.. ( Red Hat Linux Ver.10 )
Please help me..
Thanks in adv.. (1 Reply)
Hi,
Iam using BSNL broad band connection and i have installed two OS Xp & Sun solaris -x86 on my machine.Iam able to use INTERNET on windows Xp but not able to do it on solaris x86.
I have tried using DHCP concept as well as sys-unconfig command in solaris but no results.
When i use... (5 Replies)
Dear freinds...
I downloaded solaris for x86 and was able to configure the lan correctly.. I can ping and share with other destops through lan... but still I can't connect to internet ? can you please help..
I put my default gateway which is 192.168.1.1 to /etc/defaultrouter but with no use..... (13 Replies)
I have installed Oracle VM virtual box on Windows 7 and using LINUX (backtrack 5) as my virtual OS. The problem is i'm unable to connect to internet from my virtual OS. i'm using USB dongle (mobile broad band) to connect to internet from my host OS windows 7.
I tried setting NAT in VM settings... (0 Replies)
Hi,
I have a wired internet connection of hathway provider. I would like to use the connection on my desktop as well as my laptop. My desktop pc has windows 7 and yesterday I installed slackware 14.1 (full installation) on my lenovo 3000 n100 laptop.
Previously I had slacko puppy 5.7... (7 Replies)
Hello,
I just installed CentOS 7 (Server with GUI) and guess what I could install Virtual Box Guest additions without installing any extra package/software which is great news !
Now bad news or not so great news.
My Host OS is Windows 10, Virtual Box is the virtualization software. CentOS7-1... (0 Replies)
Hello, I installed FreeBSD 10.3 on AQEMU. I can't connect to internet in none
of the modes of "Default, User-Mode Networking" and "TUN/TAP Networking".
I am able to ping my host in the TAP networking mode (192.168.1.33 which is my
IP addr in guest), but getting 'no route to host' for any... (1 Reply)
Discussion started by: temp-usr
1 Replies
LEARN ABOUT SUSE
ifndp-proxy
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)ifsysctl(8)sysconfig December 2009 IFNDP-PROXY(5)