I need to login into multiple servers thru a script run couple commands and run find command as root. I only have ssh access to the servers as a user than I can "su" to root. If you have a similar script please post it. Also if you can suggest commands that I should consider please let me know.
... (1 Reply)
Hi guys , i have 1 problem and no find what is the problem...:confused:, and .netrc is configured and correct permissions...
REMOTE="/home/user"
LISTADO=`cat /root/home/user/LISTADO.txt`
MACHINE=$(echo $i|awk 'FS="|" {print $1}')
for i in $LISTADO
do
ftp $MACHINE <<TER
passive
prompt... (2 Replies)
Dear Experts,
how to run multiple scp commands from single scripts.
In a directory oracle redo files accumulate. i would like to copy those redo logs to my standby server. For same i am using scp to copy the files. where i am monitoring that as it is sending the files sequentially most of... (1 Reply)
FILE_LIST="{a.txt,b.txt,cal*}"
scp -r $..$REMOTE_PATH$FILE_LIST $LOCAL_PATH
This script passes only when all the three files are transfere, wat if only two file are transfered, but still I was to make the return code as pass.
is it possible. (2 Replies)
Experts,
Im trying to remote into a server, run a script that resides on that server and capture the information displayed & store in a local file.
I struggled with this yesterday & finally that script is working now.
Now, here is a scope creep and the script that I wrote for 1 remote... (2 Replies)
Hi Folks,
I was given a task to append three IP's at the end of a specific (and unique) line within a file on multiple servers.
I was not able to do that with the help of a script. All I could was:
for i in server1 server2 server3 server4
do
ssh $i
done
I know 'sed' could be used to... (5 Replies)
Hello All,
I am new to scripting and I am trying to write a script which can scp a file from one box to multiple boxes.
I am thinking to do like this.
1) create a file with list of all server names
2)write a script which will pick up each server line by line from server list and copy it to... (1 Reply)
Hi,
I am new to scripting and i am trying to use below script to copy code to multiple servers and multiple locations on each server. the script is not working or doesnt give any error. Any help is appreciated. basically i want a script to get the code from a location (dir below) and read the... (2 Replies)
I need to run a script on a bunch of remote servers. how can this be done without ssh into each individual server and run it
its under /sbin/script.sh on each server (1 Reply)
Hi
I did the following script to ping multiple servers, but I keep on receiveing duplicate emails for one server that is down:
#!/bin/bash
date
cat /var/tmp/servers.list | while read output
do
ping -c 1 "$output" > /dev/null
if ; then
echo "node $output is up"
else
... (10 Replies)
Discussion started by: fretagi
10 Replies
LEARN ABOUT DEBIAN
ntpd.conf
NTPD.CONF(5) File Formats Manual NTPD.CONF(5)NAME
ntpd.conf - Network Time Protocol daemon configuration file
DESCRIPTION
This manual page describes the format of the ntpd(8) configuration file.
The optional weight keyword permits finer control over the relative importance of time sources (servers or sensor devices). Weights are
specified in the range 1 to 10; if no weight is given, the default is 1. A server with a weight of 5, for example, will have five times
more influence on time offset calculation than a server with a weight of 1.
ntpd.conf has the following format:
Empty lines and lines beginning with the `#' character are ignored.
Keywords may be specified multiple times within the configuration file. They are as follows:
listen on address
OpenNTPd has the ability to sync the local clock to remote NTP servers and, if this directive is specified, can act as NTP server
itself, redistributing the local clock.
Specify a local IP address or a hostname the ntpd(8) daemon should listen on to enable remote clients synchronization. If it
appears multiple times, ntpd(8) will listen on each given address. If `*' is given as an address, ntpd(8) will listen on all local
addresses. ntpd(8) does not listen on any address by default. For example:
listen on *
or
listen on 127.0.0.1
listen on ::1
sensor device [correction microseconds] [weight weight-value]
Specify a timedelta sensor device ntpd(8) should use. The sensor can be specified multiple times: ntpd(8) will use each given sen-
sor that actually exists. Non-existent sensors are ignored. If `*' is given as device name, ntpd(8) will use all timedelta sensors
it finds. ntpd(8) does not use any timedelta sensor by default. For example:
sensor *
sensor udcf0
An optional correction in microseconds can be given to compensate for the sensor's offset. The maximum correction is 127 seconds.
For example, if a DCF77 receiver is lagging 15ms behind actual time:
sensor udcf0 correction 15000
server address [weight weight-value]
Specify the IP address or the hostname of an NTP server to synchronize to. If it appears multiple times, ntpd(8) will try to syn-
chronize to all of the servers specified. If a hostname resolves to multiple IPv4 and/or IPv6 addresses, ntpd(8) uses the first
address. If it does not get a reply, ntpd(8) retries with the next address and continues to do so until a working address is found.
For example:
server 10.0.0.2 weight 5
server ntp.example.org weight 1
To provide redundancy, it is good practice to configure multiple servers. In general, best accuracy is obtained by using servers
that have a low network latency.
servers address [weight weight-value]
As with server, specify the IP address or hostname of an NTP server to synchronize to. If it appears multiple times, ntpd(8) will
try to synchronize to all of the servers specified. Should the hostname resolve to multiple IP addresses, ntpd(8) will try to syn-
chronize to all of them. For example:
servers pool.ntp.org
FILES
/etc/openntpd/ntpd.conf
default ntpd(8) configuration file
SEE ALSO ntpd(8), sysctl(8)HISTORY
The ntpd.conf file format first appeared in OpenBSD 3.6 .
$Mdocdate: October 2 2007 $ NTPD.CONF(5)