07-02-2008
you can check the current patch level by doing uname -a
See if your kernel level is lower of that is shown from
Sun Microsystems
Solaris 8, 9 and 10 have diff latest kernel patch levels.
7 More Discussions You Might Find Interesting
1. Solaris
Hi,
how do you check that the latest service packs/patches are installed on the server, When i look at the OS Modules file, all i see is these numbers like 117176-02 etc, what is currently the latest patch level for sunOS 5.9?
thnaks (1 Reply)
Discussion started by: narik007
1 Replies
2. Solaris
required Solaris 5.10 Kernel patch 137111-03
required Solaris 5.10 Fibre Channel Device Driver patch 125184-08
I want to know about the descriptions and what the patches will do. I searched www.sun.com (patches/updates) but don't see I am looking for. (1 Reply)
Discussion started by: Y4Net
1 Replies
3. Linux
Hi
Do let me know how to find OS Patch 's installed on Linux server ?
Thanks
~ SPai (3 Replies)
Discussion started by: sbanala
3 Replies
4. AIX
Hi,
How to find out patch level in AIX and what patches are installed on AIX box?
As per my knowledge oslevel -s will give service and maintanance level description , but regarding patch level any command is there?
Regards,
Manoj (1 Reply)
Discussion started by: manoj.solaris
1 Replies
5. Solaris
I have a Solaris 10 OS having kernal patch level 138888-03 on several servers but recenlty I upgraded it into 142900-12 on some T-Series servers & v890 server after install them my syslog is increasing at a rate of 1GB on average on all servers . I believe its a bug, can somebody help me in... (1 Reply)
Discussion started by: sb200
1 Replies
6. Solaris
how can i know the patch level in solaris 10?
is there a command to know what patchs installed in my solaris?
i mean is there any tool i can run to know that other than pkginfo | more?
i need to make an inventory of all my SUN servers.
i can run explorer in all the machines but unfortunately i... (3 Replies)
Discussion started by: q8devilish
3 Replies
7. Solaris
Hi,
Anyone able to advise on how to find the kernel patch level of an ABE?
showrev and uname -a will provide kernel patch details of the running environment, but how can I run these commands against the ABE or where do these commands get their information from i.e. is the kernel patch level... (3 Replies)
Discussion started by: CiCa
3 Replies
LEARN ABOUT NETBSD
shape_patch
SHAPE_PATCH(1) General Commands Manual SHAPE_PATCH(1)
NAME
shape_patch - shapeTools RMS generate patch file
SYNOPSIS
shape patch OLDRELEASE=<name1> NEWRELEASE=<name2> [PATCHFILE=<filename>]
DESCRIPTION
Shape patch generates a patch file for updating $(OLDRELEASE) to $(NEWRELEASE). Both releases are identified by release names associated
with the macros OLD-/NEWRELEASE on the command line. Valid release names are those generated by any of the shape_RMS (pre-)release building
procedures (see shape_releas(1)). Performing 'vl -all' with the release identification file as argument usually gives a good overview of
existing release names. Patch generation happens recursively over all subsystems being part of the current node. Hence, triggering shape
patch from the top node of the central source repository creates a patch file for the whole system.
The output of shape patch is stored in a file named <name1>+2+<name2>.pat. When the PATCHFILE macro is set on the command line, $(PATCH-
FILE) is taken as output file name instead. Defining PATCHFILE=- on the command line causes the patch to be written to standard output.
Note: For patches invoking multiple subsystems, $(PATCHFILE) should be set to an absolute pathname. If not, the patch generation procedure
will leave an equally named patch file for each visited subsystem.
The patch is constructed using the vdiff(1) command and can be applied to any installation of $(OLDRELEASE) by invoking patch(1).
INCONVENIENCES
On System V machines, the generated patch file name will almost certainly exceed the 14 characters filename length limit.
SEE ALSO
shape_releas(1), vdiff(1), patch(1)
FILES
<name1>+2+<name2>.pat
28.9.119 SHAPE_PATCH(1)