Visit Our UNIX and Linux User Community


Adding robot and drives

 
Thread Tools Search this Thread
Special Forums Windows & DOS: Issues & Discussions Adding robot and drives
# 1  
Old 04-27-2011
Adding robot and drives

Hi All

Im running veritas netbackup 6.5.5, on MWindows 2003 master server.
Ive just added a Quantum PX500 with 2 drives, the problem im facing is that now under the storage unit tab on console all the storage unit types for NDMP have the new robot listed and not the original one. The set up i need is to have the old robot TLD0 listed.
Can anyone help, the robot and drives were added via Configure storage devices Wizard.. The original robot is a ADIC 500 8 drive library.

Previous Thread | Next Thread
Test Your Knowledge in Computers #838
Difficulty: Medium
Both SMTP and HTTP are valid application layer protocols used as transport for SOAP.
True or False?

6 More Discussions You Might Find Interesting

1. Hardware

Arduino Robot Tank Project

Normally I'm not into kits, but I thought my wife would enjoy this one since she is a big fan of robots and droids on StarWars! We are done with the basic mechanical assembly and starting on the electronics assembly today. The robot's "brain" consists of three levels. The Arduino board, on... (5 Replies)
Discussion started by: Neo
5 Replies

2. Solaris

Adding new hard drives on Sun SPARC T5440 server with Solaris 10

I need to add two new hard drives of 300 GB capacity to a SunSPARC T5440 server. The server currently has two hard drives of 146 GB each. How do I add the new drives to the existing UFS? What are the procedures involved in setting this server with the new hard drives? I am very new to Solaris... (6 Replies)
Discussion started by: ramatnmcc
6 Replies

3. Solaris

Adding new tape drives

hi, i am using Solaris 8 on a sparc box and already have 4 tape drives in a backup libaray attached to my unix server. we have recently added 2 new tape drives to the libaray and now want to get unix to see them. have it working in windows. how do i scan for new hardware and add theses new... (5 Replies)
Discussion started by: dshakey
5 Replies

4. Solaris

Adding logical drives

Hello, I have checked in here as I dont have enough experience as Solaris Admin. My Solaris seems to boot ok on a HP Proliant DL380 G6 server The release is 5.10, the kernel ID is Generic_137138-09. It was installed after creating one logical drive type RAID1, size 300GB. Now 2 further... (2 Replies)
Discussion started by: fogarino
2 Replies

5. Filesystems, Disks and Memory

Help adding new hard drives

Folks; I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version. Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Discussion started by: Katkota
3 Replies

6. Shell Programming and Scripting

how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX

hi how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX? thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
MLXCTL(8)						    BSD System Manager's Manual 						 MLXCTL(8)

NAME
mlxctl -- Mylex DAC960 family management utility SYNOPSIS
mlxctl [-f dev] [-v] [-a] status [drive] [...] mlxctl [-f dev] [-a] detach [drive] [...] mlxctl [-f dev] [-a] check [drive] [...] mlxctl [-f dev] rebuild channel:target mlxctl [-f dev] cstatus mlxctl [-f dev] rescan mlxctl [-f dev] config DESCRIPTION
The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices. The following options are available: -a Apply the action to all drives attached to the controller. -f dev Specify the control device to use. The default is /dev/mlx0. -v Increased verbosity. The following commands are available: cstatus Display the controller's current status. status Display the status of the specified drives. This command returns 0 if all drives tested are online, 1 if one or more drives are critical and 2 if one or more are offline. rescan Re-scan the logical drive table, and attach or detach devices from the system as necessary. detach Detach the specified drives. Drives must be unmounted and unopened for this command to succeed. check Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5). This command returns imme- diately. The status command can be used to monitor the progress of the check. rebuild Rebuild onto the specified physical drive. Note that there can be only one running rebuild operation per controller at any given time. This command returns immediately. The cstatus command can be used to monitor the progress of the rebuild. config Write the current system drive configuration to stdout. EXAMPLES
Display the status of drive ld3 attached to the controller mlx1: mlxctl -f /dev/mlx1 -v status ld3 SEE ALSO
ld(4), mlx(4) HISTORY
The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD. BUGS
Modifying drive configuration is not yet supported. Some commands do not work with older firmware revisions. Error log extraction is not yet supported. BSD
April 10, 2000 BSD

Featured Tech Videos