Setting SSH port

Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers Setting SSH port
# 1  
Old 07-07-2002
Setting SSH port

How can I switch the port which SSH listens on?
# 2  
Old 07-08-2002
Never mind, I got it. I just edited the config file Smilie
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Red Hat

Serial Port Setting Automatically changes

I am trying to change the setting of serial port baud rate in Red Hat Linux 5.9 by the following command. >> stty 9600 cs8 -parenb -ixon -cstopb -echo -F /dev/ttyS0 The serial port will be used by our custom application in 2 separate servers which are the replica of one another. The port setting... (2 Replies)
Discussion started by: Anjan Ganguly
2 Replies

2. Red Hat

Setting serial port configuration

I have 1 serial port (9 Pin) attached with my Linux server.If I give $dmesg | grep tty , it provides me the following. ttyS0 and ttyS1. I have 1 COM port with my server mother board. I have 1 customized application that requires this COM port to be used. The parameter to be set for COM port... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies

3. IP Networking

SSH Port Forwarding - sharing the same port

Hi Linux/Unix Guru, I am setting Linux Hopping Station to another different servers. My current config to connect to another servers is using different port to connect. e.g ssh -D 1080 -p 22 ssh -D 1081 -p 22 Now what I would like to have... (3 Replies)
Discussion started by: regmaster
3 Replies

4. IP Networking

Is there any way to add an exception for a port in the firewall setting, permanently?

Hello, I want to add a port in the firewall exception list so that my application can be accessed over network even if firewall is disabled. I am using iptables command to add exception. The problem is, after setting the rule if I change the firewall setting i.e. on/off then it is overwriting... (1 Reply)
Discussion started by: senrooy
1 Replies

5. UNIX for Advanced & Expert Users

check remote switch port speed setting

Hi, Someone told me how to check the remote switch port's speed setting on the other end of the cable, from linux. I forgot it. Anyone knows? I checked dmesg, ethtool (haven't checked this out thoroughly) , no luck. thanks, Marc (1 Reply)
Discussion started by: marcpascual
1 Replies

6. IP Networking

Setting up port mirroring on LINUX

Hello everyone. I am supposed to configure port mirroring on Linux (the LAN traffic needs to be routed to the other interface and passed a copy to network monitoring software): eth0 - connected to local traffic eth1 - connected to the Internet The machine is running CentOS v4.4 (Server... (1 Reply)
Discussion started by: reminiscent
1 Replies

7. Solaris

Setting up SSH - first time

Good day to you all. I have a server (running on SunOS 5.8) that i always got into via telnet. I have eventually decided to block telnet access to it and instead look toward using SSH. The problem is, whne i establish the SSH connection via PuTTy, i get the "Log in as" prompt, but upon... (5 Replies)
Discussion started by: de049
5 Replies

8. IP Networking

network speed not tale with the port setting

Hi all, one of my Sun Box facing the problem. The network port i had set to Auto-Negotiated and i had edited the /etc/system/ file in the Sun box as below: set hme:hme_adv_autoneg_cap=1 set hme:hme_adv_100fdx_cap=0 set hme:hme_adv_100hdx_cap=0 But when i checked the /var/adm/messages/, it... (0 Replies)
Discussion started by: AirWalker83
0 Replies

9. AIX

ssh setting

I would like to implement the secure shell environment in order for me to close all telnet and ftp ports. 1) Anyone can assist to give me a steps of what to do so that I can implement the ssh on my AIX5.3 server. 2) Currently I have installed putty in my PC to replace telnet directly into the... (11 Replies)
Discussion started by: kwliew999
11 Replies

10. UNIX for Dummies Questions & Answers

Setting com port questions

I have a piece of equipment, a Baytech RPC-3, that I need to communicate with through the com port. I normally use this equipment at home and am able to connect to it without problems using FC5 and minicom; I brought the equipment into work and cannot get my pc, using Suse 10 and minicom to... (0 Replies)
Discussion started by: thumper
0 Replies
Login or Register to Ask a Question