Login or Register to Ask a Question and Join Our Community


UNIX for Dummies Questions & Answers

network interface questions

 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers network interface questions
# 1  
Old 09-22-2001
network interface questions
I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is running 100 full)?
Thanks
# 2  
Old 09-24-2001
ifconfig -a
# 3  
Old 09-24-2001
This is what I get from inconfig:
# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
hme0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.0.2 netmask ffffff00 broadcast 192.168.0.255
ether 8:0:20:90:ba:70
# 4  
Old 09-25-2001
http://sunsolve.sun.com/pub-cgi/search.pl


Read Document # 17416
and every other doc in that page...
 
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

2. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

3. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

4. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

6. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

7. Solaris

Network interface configuration

Dears, i follow this to configure Network interface for my PC O/S : Unix Sun Solaris vi /etc/hostname.bge0 and write my ip vi /etc/netmasks and write my subnetmask vi /etc/defautrouter and write my gatwey vi /etc/resolv.conf and write my DNS after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies

8. Solaris

Network Interface Issue

Hi all, Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP. - - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies

9. Linux

Get info on network interface

Hello everybody, How can link network interface to the output of lspci -vv. Basicly i need to know who is the manufacturer of a specific interface, for example eth0 {Is it an Intel, or Broadcome, or something else}. Is there a way to find that out? Thanx (5 Replies)
Discussion started by: aleksey
5 Replies

10. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies
Login or Register to Ask a Question