Heartbeat configuring in Redhat

10 More Discussions You Might Find Interesting

1. Red Hat

configuring MYsql db on redhat cluster

Hello, can someone please suggest me in configuring the mysql db on redhat cluster, I have few questions. 1. where do I have to configure heart beat links, and is there any file in the redhat cluster that we update it to use these ipaddress and these interface on the node. 2. I am configuring...

2. UNIX for Advanced & Expert Users

LVS AND HEARTBEAT

Hi there, anybody can help me get a manual or a website where LVS and Heartbeat for UBUNTU (please not for REDHAT ) is hosted. Any help will be much appreciated. neuvin

3. IP Networking

Configuring DNS Server in Linux Redhat

Can someone help with a detail step-by-step oh how to configure DNS server on Linux Server. - I need to have 3 IP addresses map to a single hostname. for clients I'm a Linux rookie. Thanks Oscar

4. AIX

Heartbeat network down

Hello. I have a cluster with two heartbeat networks. Both are on separate VG. Some one varyoned those Vg's on one node. After that heartbeat network went down on both nodes. I varyoffed those two Vg's networks came back up but cluster is still in UNSTABLE status and in hacmp.out...

5. Cybersecurity

Heartbeat configuring issue

hi i'm configuring linux heartbeat in my two redhat boxes i have below few things to clarify can i set up heartbeat between two different notworks? (e.g primary server IP is 192.168.x.x and secondary server IP is 10.48.X.X) i got below error in my secondary server once primary is down ...

6. Solaris

VCS heartbeat

we have a vcs cluster set up and noticed that they were showing one of the heart beat link qfe3 as DOWN. Both qfe2 and qfe3 were fine all along, btw if I were to push in/re-set the hb cable, do you know whether it will panic or cause anything to the system,? Its a DB critical prod nodes

7. UNIX for Advanced & Expert Users

Linux heartbeat on redhat 4:node dead

Hi. I have started heartbeat on two redhat servers. Using eth0. Before I start heartbeat I can ping the two server to each other. Once I start heartbeat both the server become active as they both have warnings that the other node is dead. Also I am not able to ping each other. After stopping...

8. Red Hat

Problem with configuring host name in Redhat Linux 5

Hi All when I give the command, $ ping <hostname> I get the following error ping: unknown host <hostname> I have checked in the following files, /etc/sysconfig/network /etc/hosts /etc/resolv.conf /etc/nsswitch.conf Every where in these files host name and IP address are given...

9. Linux

linux-heartbeat on Solaris 9

has anyone installed linux-heartbeat on Solaris 9?? If yes, which version??? which is the best compiler to build it?? cc, ucbcc, gcc?? what other packages are needed to build it besides m4, autoconf, automake and libtool?? what GNU tools are needed??? thanks a lot

10. Programming

checking the heartbeat of the online user

hello, Can anyone please tell me how can i check the availability of the online user in a client-server environtment. This is for a program where lakhs of client are connected to the server and the server has to check the availability of the every client in every minute. So polling every client...

LEARN ABOUT SUSE

heartbeat

HEARTBEAT(8)						  System administration utilitie					      HEARTBEAT(8)

NAME

       heartbeat - Heartbeat subsystem for High-Availability Linux

DESCRIPTION

       heartbeat is a basic heartbeat subsystem for Linux-HA. It will run scripts at initialisation, and when machines go up or down. This version
       will also perform IP address takeover using gratuitous ARPs. It works correctly for a 2-node configuration, and is extensible to larger
       configurations.

       It implements the following kinds of heartbeats:

       o   UDP/IP broadcast;

       o   UDP/IP multicast;

       o   UDP/IP unicast;

       o   Bidirectional Serial Rings ("raw" serial ports) -- this type is deprecated and should no longer be used;

       o   special "ping" heartbeats for routers, etc. -- this type has been superseded by functionality in pacemaker() and should no longer be
	   used.

       Comprehensive documentation on heartbeat is available in the Heartbeat User's Guide. If this documentation is not installed on your system,
       it can be found at http://linux-ha.org/.

OPTIONS

       The following options are supported by heartbeat:

       -d
	   Increment debugging level. Higher levels are more verbose.

       -r
	   Reload heartbeat. This option is functionally identical to sending a running heartbeat process a HUP signal. If the configuration has
	   not changed, then this option is essentially a no-op. If ha.cf(5) or authkeys(5) has changed, then heartbeat will re-read these files
	   and update its configuration.

	   This option may not be used together with -R.

       -k
	   Kill (stop) heartbeat.

       -s
	   Report heartbeat status.

       -R
	   Heartbeat restart exec flag (internal use only). May not be used with -r.

       -C
	   Heartbeat current resource state for restart (internal use only). Only valid with -R.

       -V
	   Print out heartbeat version.

       Note that most of these options are used for supporting the heartbeat init script, which provides the conventional start, stop, status and
       restart options (among others). It is recommended to use this rather than invoking the heartbeat command directly.

SEE ALSO

       ha.cf(5), authkeys(5)

AUTHORS

       Alan Robertson <alanr@unix.sh>
	   heartbeat

       Juan Pedro Paredes Caballero <juampe@retemail.es>
	   man page

       Simon Horman <horms@verge.net.au>
	   man page

       Florian Haas <florian.haas@linbit.com>
	   man page

Heartbeat 3.0.5 						    24 Nov 2009 						      HEARTBEAT(8)

UNIX for Dummies Questions & Answers