controlling traffic source from NIC eth0, eth1 in Linux

9 More Discussions You Might Find Interesting

1. IP Networking

Why eth1 with auto dhcp disturbs pppoe over eth0?

Hi, I use ubuntu 16.04 desktop with ufw (default setup + 22, 80, 443 ports open). I connect directly to ISP using pppoe over eth0. I also have eth1 which when disabled the websites are accessible in browser. When starting eth1 with auto dhcp the websites are no longer accessible in browser (give...

2. Red Hat

Dual NICs - When I 'ifup eth1' it replaces eth0

I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it...

3. Debian

[HELP] How to create a NIC eth0 in CentOs 6.3.

I make many service in Centos 6.3 so I clone and copy any edition to do, but I don't see a NIC eth0, What I have to do to used eth0 ?, and how to create it ? It some picture: http://i1055.photobucket.com/albums/s505/vn_photo/2222.jpg http://i1055.photobucket.com/albums/s505/vn_photo/1111.jpg ...

4. Red Hat

Wan on eth1 and Lan on eth0

I have a local network on dev eth0 Server has static IP of 10.0.0.1 Gateway is 10.0.0.1 and Dns is 10.0.0.1 I am using this network for imaging 500 plus computer... Now, Issue that I am having is that I need to update packages and I dont want to change the configuration on eth0 because I...

5. IP Networking

Problem in eth0 and eth1 sharing internet with other computers

hellow everbody. iam using 32 bit centos 6.2 on my desktop and iam new to linux. i have eth0 and eth1 on my desktop. so i have some problems i have menson here: i have edited: etc/sysctl.conf net.ipv4.ip_forward = 1 and i have edited iptables too # iptables -t nat -A...

6. Ubuntu

Ubunut iptable not routing trafic between eth1 and eth0

hello, first of all i am new to unix so maybe my problem is very easy for many of you but is very important to me. So the idea is that i want to use a ubuntu 10.4 machine as a router from eth0 to eth1. but the traffic routing is nor working properly i configured the 2 interfaces to be...

7. IP Networking

Splitting eth0 traffic into two virtual interface

Hello everybody, I have been reading many posts about this topic but I have no figure out how to solve it. I need to split the traffic incoming on eth0 on two other interfaces (for instance one receiving on port 80 and the others on the other interface). I cannot understand how to do that....

8. Solaris

Reg- eth0,eth1 (ethernet card)

Hi Guys, I am working as a L-1 support and i want to know that are the precaution need to take on eth0(Ethernet card) i heard on production server it is very much important, what are the steps need to observe on this tickets.

9. Red Hat

ifcfg-eth0 and eth1 is N/A

when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in /etc/sysconfig/network-scripts/. what will i do?

LEARN ABOUT SUNOS

tc-matchall

Match-all classifier in tc(8)					       Linux					     Match-all classifier in tc(8)

NAME

       matchall - traffic control filter that matches every packet

SYNOPSIS

       tc filter ... matchall [ skip_sw | skip_hw  ] [ action ACTION_SPEC ] [ classid CLASSID ]

DESCRIPTION

       The matchall filter allows to classify every packet that flows on the port and run a action on it.

OPTIONS

       action ACTION_SPEC
	      Apply an action from the generic actions framework on matching packets.

       classid CLASSID
	      Push matching packets into the class identified by CLASSID.

       skip_sw
	      Do  not  process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter-
	      face, operation will fail.

       skip_hw
	      Do not process filter by hardware.

EXAMPLES

       To create ingress mirroring from port eth1 to port eth2:

	      tc qdisc	add dev eth1 handle ffff: ingress
	      tc filter add dev eth1 parent ffff:	    
		      matchall skip_sw			    
		      action mirred egress mirror	    
		      dev eth2

       The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it  that
       mirrors the packets to device eth2.

       To create egress mirroring from port eth1 to port eth2:

	      tc qdisc add dev eth1 handle 1: root prio
	      tc filter add dev eth1 parent 1:		     
		      matchall skip_sw			     
		      action mirred egress mirror	     
		      dev eth2

       The  first  command  creats  an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a
       matchall filters on it that mirrors the packets to device eth2.

       To sample one of every 100 packets flowing into interface eth0 to psample group 12:

	      tc qdisc add dev eth0 handle ffff: ingress
	      tc filter add dev eth0 parent ffff: matchall 
		   action sample rate 100 group 12

SEE ALSO

       tc(8),

iproute2							    21 Oct 2015 				     Match-all classifier in tc(8)

UNIX for Dummies Questions & Answers