Sco openserver 6 on hd sata: cloning

Top Forums UNIX for Beginners Questions & Answers Sco openserver 6 on hd sata: cloning

07-11-2018

Registered User

2,202, 340

Join Date: Apr 2007

Last Activity: 10 May 2020, 8:59 AM EDT

Location: 44.21.48N 80.50.15W

Posts: 2,202

Thanks Given: 3

Thanked 340 Times in 306 Posts

no. you install the sco version on your current sco system.

You are going to download edgesco6.elf from Microlite Corporation - BackupEDGE DOwnloads
Then install this on your SCO system.
Start the edgemenu program and configure the backup device.
Do a full backup.
Create the emergency boot media.
Shut down the system and replace the disk with a 128gb SSD.
Boot from the emergency boot media and do a one touch restore.
Leave the 1tb disk on the shelf as the hot spare.

Last edited by jgt; 07-11-2018 at 11:45 AM..

jgt

View Public Profile for jgt

Visit jgt's homepage!

Find all posts by jgt

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. SCO

SCO Unix 5.0.6 SATA in compatibility mode

I am very new to SCO Unix so I apologize if this is a easy or dumb question. I have a 160GB SATA hard drive and SATA CD-ROM drive connected to one of my systems. I have both the drives running in compatibility mode. I also have the hard drive set as a primary master and the CD-ROM drive set as...

2. SCO

Install Hang OpenServer 6 - SATA CDROM

Hi all Can anybody offer any help with installing Openserver 6 on a Supermicro server? I am familiar with installing OS5, but this is my first time with v6. The PC is fitted with Supermicro X8DTL-I Dual Xeon motherboard and 2 Xeon E5620 processors, and 16Gb Ram, LSI MegaRaid SAS8708 8 port...

3. Hardware

Connect SATA Laptop HardDrive to Desktop SATA Slots

Hello everybody, I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors. The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my...

4. SCO

SATA Hard Disk support by SCO OpenServer 5.05

Is SATA hard disk is suooprted by SCO OpenServer 5.05? If No, how to couter this problem. If yes, please provide the installation steps.

5. SCO

SATA AHCI Tape on SCO 5.0.7

Dear all, I'm newbie in SCO. I already purchase SCO 5.0.7 and SATA Tape Drive (not SCSI) for IBM server. not a cheap investment :( my problem is: I can't use my sata tape on sco 5.0.7 for backup my data because sco can't detect any sata tape has been plug into o/s. i already running "mkdev...

6. SCO

sco openserver 5.0.7

Dear members when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config. i tried MP4, EFS 5.64,5.70A but not solved the problem..

7. UNIX for Dummies Questions & Answers

SCO Openserver 6.0

Hi guys, I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not...

8. UNIX for Advanced & Expert Users

SCO 5.0.2 openserver

I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals?

9. UNIX for Dummies Questions & Answers

sco openserver 5.5

hello! when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ? kindly help me thanks

10. UNIX for Dummies Questions & Answers

Help For SCO OpenServer

I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work i need to change the mouse configuration, ...

LEARN ABOUT SUSE

getfdprm

getfdprm(1)                                                   General Commands Manual                                                  getfdprm(1)

Name
       getfdprm - print the current format information

Note
       This  manpage has been automatically generated from fdutils's texinfo documentation.  However, this process is only approximative, and some
       items, such as cross-references, footnotes and indices are lost in this translation process.  Indeed, these items have no appropriate  rep-
       resentation  in  the  manpage  format.  Moreover, only the items specific to each command have been translated, and the general information
       about fdutils has been dropped in the manpage version.  Thus I strongly advise you to use the original texinfo doc.

       *      To generate a printable copy from the texinfo doc, run the following commands:

                     ./configure; make dvi; dvips fdutils.dvi

       *      To generate a HTML copy,  run:

                     ./configure; make html

              A pre-made HTML can be found at: `http://www.tux.org/pub/knaff/fdutils'

       *      To generate an info copy (browsable using emacs' info mode), run:

                     ./configure; make info

       The texinfo doc looks most pretty when printed or as HTML.  Indeed, in the info version certain examples are difficult to read due  to  the
       quoting conventions used in info.

Description
          getfdprm [drive]

       getfdprm prints the current geometry information for drive .  This information can be set using setfdprm

See Also
       Fdutils' texinfo doc

fdutils-5.5                                                           03Mar05                                                          getfdprm(1)

UNIX for Beginners Questions & Answers