10 More Discussions You Might Find Interesting
1. SCO
I am very new to SCO Unix so I apologize if this is a easy or dumb question.
I have a 160GB SATA hard drive and SATA CD-ROM drive connected to one of my systems. I have both the drives running in compatibility mode. I also have the hard drive set as a primary master and the CD-ROM drive set as... (10 Replies)
Discussion started by: NPIGuy
10 Replies
2. SCO
Hi all
Can anybody offer any help with installing Openserver 6 on a Supermicro server?
I am familiar with installing OS5, but this is my first time with v6.
The PC is fitted with Supermicro X8DTL-I Dual Xeon motherboard and 2 Xeon E5620 processors, and 16Gb Ram, LSI MegaRaid SAS8708 8 port... (11 Replies)
Discussion started by: millosman
11 Replies
3. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
4. SCO
Is SATA hard disk is suooprted by SCO OpenServer 5.05? If No, how to couter this problem. If yes, please provide the installation steps. (2 Replies)
Discussion started by: rakeshkumar9919
2 Replies
5. SCO
Dear all,
I'm newbie in SCO. I already purchase SCO 5.0.7 and SATA Tape Drive (not SCSI) for IBM server. not a cheap investment :(
my problem is:
I can't use my sata tape on sco 5.0.7 for backup my data because sco can't detect any sata tape has been plug into o/s. i already running "mkdev... (7 Replies)
Discussion started by: asumatezuka
7 Replies
6. SCO
Dear members
when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config.
i tried MP4, EFS 5.64,5.70A but not solved the problem.. (0 Replies)
Discussion started by: M_farooqui
0 Replies
7. UNIX for Dummies Questions & Answers
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies
8. UNIX for Advanced & Expert Users
I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
Discussion started by: SCOoT
3 Replies
9. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
10. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
createhdf(1) Emulators createhdf(1)
NAME
createhdf - Create a blank IDE hard disk image in .hdf format
SYNOPSIS
createhdf [ -c ] [ -s ] cylinders heads sectors file
DESCRIPTION
createhdf creates a blank image of an IDE hard disk in .hdf format for use with Sinclair ZX Spectrum emulators.
OPTIONS
-c specifies that the .hdf image should be created in `compact' mode, where only the low byte of every word is stored in the image.
This is useful for saving space if the hard disk image is for use with an interface which accesses only the low byte of every word.
-s specifies that the .hdf image should not be created as a sparse file. Normally, createhdf will attempt to create the hard disk image
as a `sparse file', where the operating system knows that the file consists mostly of zero bytes and fills those in without using
any space in the file. This option disables this. (There's nothing `magic' about this: if data is written to the file, it will take
up space just like any other data; it's only empty space which is synthesised by the operating system).
-v version
specifies the version of .hdf image to be created. Valid values are `1.0' for a version 1.0 file and `1.1' for a version 1.1 file.
Defaults to creating version 1.1 files.
cylinders
specifies the number of cylinders in the image.
heads specifies the number of heads in the image.
sectors
specifies the number of sectors in the image.
file specifies the file to which the image should be written.
BUGS
None known.
SEE ALSO
fuse(1), fuse-utils(1), libspectrum(3)
The .hdf format specification, at
http://www.ramsoft.bbk.org/hdfform.html.
The comp.sys.sinclair Spectrum FAQ, at
http://www.worldofspectrum.org/faq/index.html.
AUTHOR
Philip Kendall (philip-fuse@shadowmagic.org.uk).
Version 1.0.0 16th December, 2010 createhdf(1)