9 More Discussions You Might Find Interesting
1. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
2. HP-UX
Hi,
We cant set the listen address of my java process to the IP address or any of the DNS names listen in the hosts file of the server.
We can access the resources of the pid in the web browser through http://<IP / DNS>:port/console
Based on the pid, how can we find what is the listen... (6 Replies)
Discussion started by: mohtashims
6 Replies
3. Solaris
Good morning!
I would like to test a particular port in Solaris, to see if the firewall rules are ok.
Should I install an application, but as yet I have not, have to force solaris to keep an open door, and put any application listening to port 1099, and will test a terminal connectivity via... (5 Replies)
Discussion started by: poyato
5 Replies
4. HP-UX
Hi
I wonder if its possible to setup NTP clients running HP-UX o.s. from a solaris 10 NTP server?
FR (3 Replies)
Discussion started by: fretagi
3 Replies
5. Linux
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
Discussion started by: MichaelLi
1 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
8. UNIX for Dummies Questions & Answers
Hi all,
How can I log all requests on ports for programs like ftp, telnet, rsh, xdmcp etc...
I want to see if anyone uses these programs/protocols and how often.
Is it difficult to setup a log for these ports and listen on all requests?
/combat (4 Replies)
Discussion started by: tonlu
4 Replies
9. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
ntp(n) Tnm Tcl Extension ntp(n)
__________________________________________________________________________________________________________________________________________________
NAME
ntp - Retrieve NTP status information.
_________________________________________________________________
DESCRIPTION
The Network Time Protocol (NTP) (RFC 1119, RFC 1305) allows to synchronize computer clocks by exchanging NTP messages. The ntp command
allows to retrieve control variables from NTP peers.
NTP COMMAND
ntp [options]
Invoking the ntp command with options but without any command arguments allows to retrieve and change the default values. See the
description of supported options below. Default values are bound to a Tcl interpreter which allows to have multiple Tcl interpreter
with different defaults.
ntp [options] host arrayName
The ntp command sends a NTP version 3 mode 6 request to host and writes status information into the Tcl array arrayName. After suc-
cessful completion, the array will contain the following elements (RFC 1305):
peer.delay
This is a signed fixed-point number indicating the roundtrip delay of the peer clock relative to the local clock over the
network path between them, in seconds.
peer.dispersion
This is a signed fixed-point number indicating the maximum error of the peer clock relative to the local clock over the net-
work path between them, in seconds.
peer.offset
This is a signed, fixed-point number indicating the offset of the peer clock relative to the local clock, in seconds.
peer.precision
This is a signed integer indicating the precision of the various clocks, in seconds to the nearest power of two.
peer.reach
This is a shift register used to determine the reachability status of the peer, with bits entering from the least significant
(rightmost) end. A peer is considered reachable if at least one bit in this register is set to one.
peer.srcadr
This is the IP address of the peer.
peer.stratum
This is an integer indicating the stratum of the local clock.
peer.valid
This is an integer counter indicating the valid samples remaining in the filter register. It is used to determine the reacha-
bility state and when the poll interval should be increased or decreased.
sys.peer
This is a selector identifying the current synchronization source.
sys.precision
This is a signed integer indicating the precision of the various clocks, in seconds to the nearest power of two.
sys.refid
This is a 32-bit code identifying the particular reference clock.
sys.rootdelay
This is a signed fixed-point number indicating the total roundtrip delay to the primary reference source at the root of the
synchronization subnet, in seconds.
sys.rootdispersion
This is a signed fixed-point number indicating the maximum error relative to the primary reference source at the root of the
synchronization subnet, in seconds.
sys.stratum
This is an integer indicating the stratum of the local clock
sys.system
A textual description of the system type.
NTP OPTIONS
The following options control how NTP requests are send and how the ntp command deals with lost NTP packets.
-timeout time
The -timeout option defines the time the ntp command will wait for a response. The time is defined in seconds with a default of 2
seconds.
-retries number
The -retries option defines how many times a request is retransmitted during the timeout interval. The default number of retries is
2.
SEE ALSO
scotty(1), Tnm(n), Tcl(n)
AUTHORS
Erik Schoenfelder <schoenfr@gaertner.de>
Juergen Schoenwaelder <schoenw@cs.utwente.nl>
Tnm ntp(n)