I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID: 80b8e237.
Boot device: disk File and args:
after Boot Device:disk File and args, no respond from machine, and can not using my keybord to type some command.
I'm using hyperterminal for connect to machine. What must I do?
and how to booting from CD Master , that same with new OS installation and will delete all my file?
Hey,
Insert disk of this "problem" machine in another sparc machine. Do installation there and move this disck back into original machine. It seems that problem because of CD-Drive.
For trouble I was try using :
keyboard ctrl+break
and open break prompt
after thatusing command :
Code:
setenv diag-device disk
reset -all
boot
But after boot sttill stop in
Boot device: disk File and args:
and I try change boot device using cdrom :
Code:
setenv boot-device cdrom
get message
Quote:
boot device = cdrom
Code:
boot
and now can booting from disk but have error message :
Quote:
boot device: cdrom File and args:
SunOS Release 5.8 Version Generic_108528-13 64-bit
Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
WARNING: /pci@1f,4000/scsi@3/sd@0,0 (sd0):
Error for Command: load/start/stop Error Level: Retryable
Requested Block: 0 Error Block: 0
Vendor: IBM Serial Number:
Sense Key: Not Ready
ASC: 0x4 (LUN not ready), ASCQ: 0x0, FRU: 0x0
WARNING: /pci@1f,4000/scsi@3/sd@0,0 (sd0):
Error for Command: load/start/stop Error Level: Retryable
Requested Block: 0 Error Block: 0
Vendor: IBM Serial Number:
Sense Key: Not Ready
ASC: 0x4 (LUN not ready), ASCQ: 0x0, FRU: 0x0
any one now what mean this message and how if I reinstall my software thereis will reformat my disk and delete all existing file an configuration?
looks like a defect disk. Try boot cdrom - install,
break the install process after input hostname and
network parameters.
Than you have a shell prompt and a mini solaris in
the ramdisk. Try format and look at the output,
perhaps your disk is not labeled or its really defect.
With format you can scan the disk with scsi commands,
but your data will be lost.
Hi all,
I managed to salvage form work an old Sun Sparc Ultra 30. I have had it stored (controlled storage) for a few years and decided to get it home and boot it up.
It starts up with a beep then I can hear disks spinning up, CDROM moving but nothing is displayed on the monitor.
Can... (2 Replies)
I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10.
I've got the Oracle installation guide for it and I got as far as:
"4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive."
I don't have a CD-ROM by that name and a web search for that... (21 Replies)
I have a Sun Blade 1000 machine that I installed Ubuntu 7.10 SPARC onto. The only user configured (configure during install) cannot use sudo. When I try to issue a command using sudo (ex. sudo apt-get install) it asks me for my password and returns the error "user not found in sudoers file". I need... (4 Replies)
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Need Help , Ultra SPARC can not loading