Visit Our UNIX and Linux User Community


Solaris 11 ipadm show-if disabled


 
Thread Tools Search this Thread
Top Forums UNIX for Advanced & Expert Users Solaris 11 ipadm show-if disabled
# 1  
Old 02-03-2014
Solaris 11 ipadm show-if disabled

Hi exports,

I have a T4 with 4 port internal NIC which 2 ports are active and, external one with 4 ports as well with only 2 ports active. So the total of the ports are 4 out of 8. I have created an link aggregation called gnic0 with ports net0, net1, net6 and, net7 in it. I also created a vnic1 over gnic0. here is what I see

Code:
root@ap1g:~# dladm show-link
LINK                CLASS     MTU    STATE    OVER
net1                phys      1500   up       --
net0                phys      1500   up       --
net7                phys      1500   up       --
net6                phys      1500   up       --
net3                phys      1500   unknown  --
net2                phys      1500   unknown  --
net4                phys      1500   unknown  --
net5                phys      1500   unknown  --
net8                phys      1500   up       --
gnic0               aggr      1500   up       net0 net6 net7 net1
vnic1               vnic      1500   up       gnic0
testzone/net0       vnic      1500   up       gnic0

root@ap1g:~# dladm show-phys
LINK              MEDIA                STATE      SPEED  DUPLEX    DEVICE
net1              Ethernet             up         1000   full      igb1
net0              Ethernet             up         1000   full      igb0
net7              Ethernet             up         1000   full      nxge3
net6              Ethernet             up         1000   full      nxge2
net3              Ethernet             unknown    0      unknown   igb3
net2              Ethernet             unknown    0      unknown   igb2
net4              Ethernet             unknown    0      unknown   nxge0
net5              Ethernet             unknown    0      unknown   nxge1
net8              Ethernet             up         10     full      usbecm2

root@ap1g:~# ipadm show-addr
ADDROBJ           TYPE     STATE        ADDR
lo0/v4            static   ok           127.0.0.1/8
vnic1/v4          static   ok           xxx.xxx.30.153/24
net8/v4           static   ok           169.254.182.77/24
lo0/v6            static   ok           ::1/128

all 4 ports are up and, running. right? but, is the below behavior normal?

Code:
 root@ap1g:~# ipadm show-if
IFNAME     CLASS    STATE    ACTIVE OVER
lo0        loopback ok       yes    --
gnic0      ip       down     no     --
vnic1      ip       ok       yes    --
net1       ip       down     no     --
net8       ip       ok       yes    --
net6       ip       disabled no     --          <------------ disabled??? why
net7       ip       disabled no     --          <------------ disabled??? why
net0       ip       disabled no     --          <------------ disabled??? why

when i do snoop of all of my NICs I see traffic on all the network.
My server is running on vnic1.

Please shed some light on this.
thanks a bunch

Last edited by Don Cragun; 02-03-2014 at 04:51 PM.. Reason: Add CODE tags.

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

Ipadm showing "/?" in ADDROBJ on S11 local zone

Hi! I have a Solaris 11 local zone, everything is running fine, BUT, when I issue an "ipadm show-addr" from inside the local zone I get the following: root@xxxxxxx:/var/opt# ipadm show-addr ADDROBJ TYPE STATE ADDR lo0/? inherited ok 127.0.0.1/8... (2 Replies)
Discussion started by: rtmg
2 Replies

2. Shell Programming and Scripting

Can someone please show me a very simple "expect" script to change password in Solaris please?

Ladies & Gents, Can one of you gurus please show me a very simple "expect" script to change the password in Solaris in a script, please? Nothing fancy, no error checking, no nothing. Just to change the password of a new user, it's all. Many thanks in advance. U guys have honestly earned my... (1 Reply)
Discussion started by: Hiroshi
1 Replies

3. Solaris

Solaris 11 man pages won't show on CLI

Hello guys, I am a newbie. Just freshly installed Solaris 11. When I try to type for example root@t1000:~# man zpool It says bash: man: command not found. It used to show manual pages before installation. Any help is appreciated. Thanks. (5 Replies)
Discussion started by: nazimbilir
5 Replies

4. Solaris

Link aggregation and status of network interfaces in “ipadm” command

I am again rephrasing the issue that we are facing: We are creating link aggregations with two interfaces named net0 & net5: # dladm create-aggr -m dlmp -l net0 -l net5 -l net2 aggr1 Setting prob targets for aggr1: # dladm set-linkprop -p probe-ip=+ aggr1 Setting failure detection... (3 Replies)
Discussion started by: amitanshu.verma
3 Replies

5. Solaris

Solaris ftp connects out svc disabled.

Hi, Running ftp online 2:53:02 svc:/network/ftp:default If I disable ftp disabled 2:54:00 svc:/network/ftp:default I can still SEND ftp files out. I cannot connect to this server via FTP, but why can I still connect to other ftp servers and send files? Cheers. (5 Replies)
Discussion started by: RedWizard75
5 Replies

6. Solaris

Ipadm create failed

Hello Group, I tried to enable the net1 interface under Solaris 11 and I see a flag related with a ipmp failed. Now this interface is not set to any ipmp group. I would appreciate it your help dladm show-phys LINK MEDIA STATE SPEED DUPLEX DEVICE... (3 Replies)
Discussion started by: csierra
3 Replies

7. Solaris

NTP gets disabled

Hi experts, I am using solaris10 operating system on a N240 Sun server. I have a problem on NTP, that is, i am using an external ntp server and when i enable ntp instance via smf, it works for a while then it gets disabled.. Here these are the info: 1) I enable the ntp service: # svcadm... (1 Reply)
Discussion started by: dyavuzy1
1 Replies

8. Shell Programming and Scripting

queue is disabled

Does anyone know why I got this message when I tried to print my file on Unix? THANK YOU! (1 Reply)
Discussion started by: whatisthis
1 Replies

9. UNIX for Dummies Questions & Answers

Disabled printers

How does or what makes a printer go into a disabled state? (5 Replies)
Discussion started by: dsb0
5 Replies

Featured Tech Videos