squid: Allow access to only one site and only via 80 or 443


 
Thread Tools Search this Thread
Top Forums UNIX for Advanced & Expert Users squid: Allow access to only one site and only via 80 or 443
# 1  
Old 08-24-2012
squid: Allow access to only one site and only via 80 or 443

Can someone please give me the conf file line to allow access to myexample.com and only that site, and only through http and https?

So far I have only that site accessible via http, but all https sites are opened.

Squid 3.1 on Cent 6

---------- Post updated at 12:06 PM ---------- Previous update was at 11:17 AM ----------

Please someone, this is urgent.

Last edited by jim mcnamara; 08-24-2012 at 03:50 PM.. Reason: duplicate
Login or Register to Ask a Question

Previous Thread | Next Thread

8 More Discussions You Might Find Interesting

1. Post Here to Contact Site Administrators and Moderators

Regarding not able to access UNIX.com site

Hello MODs/Admins, Could you please help me here as from last 6 to 7 days I(and checked with my fellow friends too) am not able to access unix.com site at all. It is very very slow, it never loads completely. Even I checked with different people and different computers it results same only,... (8 Replies)
Discussion started by: RavinderSingh13
8 Replies

2. Proxy Server

How to use Squid on Linux to control certain IP to access Web Server and certain IP cannot access?

Dear all experts here, :) I would like to install a proxy server on Linux server to perform solely to control the access of Web server. In this case, some of my vendor asked me to try Squid and I have installed it onto my Linux server. I would like know how can I set the configuration to... (1 Reply)
Discussion started by: kwliew999
1 Replies

3. IP Networking

iptables allow access to one site

Hi all I need help with a set of iptables rules that would allow a portion of a bank of ipaddresses acces to only one or two named wbsites. Please advise Thank You Ed (3 Replies)
Discussion started by: wa1ed
3 Replies

4. Emergency UNIX and Linux Support

[solved] Block access to all sites except one using Squid

I need a Squid config that allows access to only one domain: .example.com Traffic should only be allowed through if coming from 10.100.0.0/24 and only port 80 (http) and port 443 (https) traffic should be allowed through, but again, only to this ONE domain. It Must be Squid (no iptables... (3 Replies)
Discussion started by: glev2005
3 Replies

5. IP Networking

Squid vs iptables = no Squid access.log?

Hello, I have a pretty useless satellite link at home (far from any civilization), so I wanted to set up caching in order to speed things up. My Squid 2.6 runs "3128 transparent" and is set up quite well on a separate machine. I also have my dd-wrt router to move all port 80 traffic through... (0 Replies)
Discussion started by: theWojtek
0 Replies

6. Emergency UNIX and Linux Support

Configure Squid to use LDAP group auth to deny internet access

Hi all We have squid-2.5.STABLE11-3.FC4 running in our environment. LDAP authentication works fine. Active Directory 2003 Users are prompted to enter credentials every time they access the net. The system works perfectly, but I need to configure Squid to block users in a specific AD group.... (1 Reply)
Discussion started by: wbdevilliers
1 Replies

7. UNIX and Linux Applications

How to redirect to squid login web page when internet access

Hi , I am new user. As you know when acl is defined in /etc/squid/squid.conf file according to its http_access users are able to access internet. Before that .htaccess asks them to access internet. It is fine. I saw in some customised linux servers in place of .htaccess login ,html web page... (1 Reply)
Discussion started by: sandeepvson
1 Replies

8. IP Networking

port access to site to site VPN

Setup a site to site VPN between two cisco routers. One of the site locations is unable to access ports such as https://example.com:9001 How do I let them go into port 9001? They can ssh, ftp, telnet and everything else. Is this a VPN issue or ACL access issue? I put permit ip host... (0 Replies)
Discussion started by: photon
0 Replies
Login or Register to Ask a Question
XmDropSiteRegister(library call)										  XmDropSiteRegister(library call)

NAME
XmDropSiteRegister -- A Drag and Drop function that identifies a drop site and assigns resources that specify its behavior SYNOPSIS
#include <Xm/DragDrop.h> void XmDropSiteRegister( Widget widget, ArgList arglist, Cardinal argcount); DESCRIPTION
XmDropSiteRegister identifies the specified widget or gadget as a drop site and sets resource values that define the drop site's behavior. The routine assigns default values to any resources that are not specified in the argument list. The toolkit generates a warning message if a drop site is registered with XmNdropSiteActivity set to XmDROP_SITE_ACTIVE and the XmNdropProc resource is NULL. If the drop site is a descendant of a widget that is registered as a drop site, the XmNdropSiteType resource of the ancestor drop site must be specified as XmDROP_SITE_COMPOSITE. The ancestor must be registered before the descendant. The drop site is stacked above all other sib- ling drop sites already registered. widget Specifies the ID of the widget to be registered. arglist Specifies the argument list. argcount Specifies the number of attribute/value pairs in the argument list (arglist). For a complete definition of DropSite and its associated resources, see XmDropSite(3). RELATED
XmDisplay(3), XmDropSite(3), XmDropSiteEndUpdate(3), XmDropSiteStartUpdate(3), XmDropSiteUpdate(3), XmDropSiteUnregister(3), and XmScreen(3). XmDropSiteRegister(library call)