10 More Discussions You Might Find Interesting
1. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
2. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
3. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
4. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
5. SCO
Hi,
I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies
6. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
7. UNIX for Dummies Questions & Answers
I've installed mandrake 9 and from the start my network card wouldn't work. I ran the network configuration wizard several times and counldn't get it to work. I checked Linux and in the boot message said the IRQ for my network card was 0 but wheni checked windows XP it listed it as 23. I have a... (1 Reply)
Discussion started by: ripmc
1 Replies
8. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
9. UNIX for Dummies Questions & Answers
Hi
I just installed linux red hat 7.0 and i can't connect the machine on the network.
Even after i run linuxconfig, when the machine reboots ethernet card eth0 fails to initialize.
Any sugestion would be welcome. (1 Reply)
Discussion started by: IMOTEB
1 Replies
10. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies